QTL, recombination frection?

22 February 2021 2,588 2 View

What are the dimensions by which the independent variable (big data) can be measured, Knowing We using the questionnaire instrument?

We have a research project consisting of three variables where big data is the independent variable. Some previous studies showed that Volume, Variety, Velocity and Veracity Are the dimensions...

21 February 2021 8,133 2 View

How can we determine the band gap of a composite material that is made up of a composition of direct and indirect band gap semiconductor materials?

I have a direct band gap material and an indirect band gap material. If I made a composite of both through physical mixing. Then how can I determine the band gap of such a material as the Tauc...

17 February 2021 8,104 4 View

What Electrolyte Solution should be used for EIS and CV, While material I'm using is Carbon doped Titania as a counter electrode in DSSC?

Hope so, you are all fine, I want to perform EIS and CV of my material Carbon doped Titania as a counter electrode for DSSC, I just want to know what electrolyte solution and in what molar...

25 December 2020 7,095 3 View

How to determine the sample size for ANOVA in GPower?

Hi, I am going to execute an experiment with the four categorical variables (A=2 levels, B=2 levels, C=2 levels, D= 5 levels) and one dependent continuous variable. There are total of 40 groups...

19 December 2020 3,600 4 View

What are the free fee journal in Scopus or Clarivate classification deal with geotechnic ?

I want to introduce my manuscript to journal which is not take fee on publishing.

15 November 2020 609 3 View

Why the crystallographic plane (100) has higher growth rate than other planes such as (220), (111) in (100) oriented crystal?

Dear All, Here I have an interesting question that comes to me about crystallographic planes and growth rate. The literature survey shows, the (100)-oriented crystals the crystallographic plane...

06 November 2020 9,490 10 View

Can we co-relate that A-site vacancies are one of the main reasons for (110)-texture formation? But how?

A-site deficient 0.1BiScO3-BaTiO3 (BSBT) thin films were deposited on Pt/TiO2/SiO2/Si substrate by using PLD. XPS results revealed that A-site vacancies increase with the increase of deposition...

05 November 2020 9,281 1 View

Difference between Data-Driven Adaptive Robust Optimization and Adaptive Robust Optimization?

Could you make some points about the difference between Data-Driven Adaptive Robust Optimization and (classic) Adaptive Robust Optimization?

01 November 2020 9,653 3 View

Can anyone tell me that how to find dangling bond in GaN, AlN or AlGaN?

I want to know about the dangling bond? by which method we can find it, does its need some special type of characterization just like XRD etc... or method i want to find dangling bond effect in...

26 October 2020 1,938 6 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

How climate change will influences human and animal behavioral change?

The role of climate change influencing the human behavior as well as economics interest

01 June 2021 0 0 View

flexibility of polymers chain

effect of double bond on the flexibility of polymers

07 April 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Formulation of polymer color flakes

I am writing to request some information for making polymer color flakes. I would appreciate the help.

17 March 2021 0 0 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View