I would like to do research on modeling and experimental study for new type of renewable fuel. Does any one have similar experience on modeling of combustion in IC engines and sensitive parameters to be optimized?
If it were at Chennai, India, I would say YES
Try Prof. Wachtmeister at TU Munich
Thank you Prof Dr. Lenkamp.
I am looking for PhD supervisor in a German university on research topic IC engine modeling. You can send me contacts via email: [email protected]
You can also try with Prof. Peter Tzscheutschler (his email address is [email protected]), he works at Technical University of Munich.
I was there for some weeks, and they have an amazing test facility for testing of cogeneration devices, based on IC and Stirling engines.
In India, ARAI tests so many automotive engines with various alternative fuels. Please contact the ARAI, Pune employees to get details.
http://waset.org/publications/14450/theoretical-modeling-and-experimental-study-of-combustion-and-performance-characteristics-of-biodiesel-in-turbocharged-low-heat-rejection-d.i-diesel-engine
Flow boiling has an advantage in higher heat flux application ideal for miniature applications. What are the limitations that govern the application of flow boiling heat transfer over sensible...
29 June 2015 2,662 2 View
Nanofluids have been attractive cooling medias in the are of high heat removal requirements. As Internal Combustion engines reject an enormous amount of heat from combustion process, using...
28 June 2015 4,450 7 View
In a fluidised bed gasification, cyclone removes the fly ash/particles leaving with the syngas, What is the best mechanism of ash removal from the bed side in the temperature range of 800-1000...
02 August 2014 1,751 10 View
It's known that low ethanol blended gasoline fuel up to E10 results in an economic save as well as a reduction in emissions with out any modification on the engine system while on the other...
06 February 2014 6,081 13 View
Nanofluids are reported to increase the thermal efficiency of a heat pipe significantly by several researchers. The possible reasons for this performance improvement is not yet clearly...
28 July 2013 9,823 0 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...
10 August 2024 6,493 1 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I have carried out MFC experiments on three different volumes, 50, 500 and 1000 mL of wastewater. Results after MFC treatment shows that TDS and EC are more in larger volumes of water i.e. TDS and...
09 August 2024 9,621 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...
06 August 2024 1,989 3 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View