24 January 2019 2 2K Report

I am working on modelling a series of laboratory core flooding experiments that involve low salinity water flooding and low salinity surfactant flooding and I would like to do the modelling in GEM.

Unfortunately, I have not used GEM and I'm short on resources on how I can do the modelling.

Can anyone please help me out on this? Thanks in advance

More Daniel Egbe's questions See All
How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?

How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?

09 August 2024 7,718 0 View

H-index issues?

Hi Sir/Madam, I would like to know why my h-index is stuck to 15 despite the number of new publications added. Could you explain me how marks are granted. Best, Daniel

28 July 2024 2,607 2 View

I'm looking for a tool to evaluate the risk of bias in... Are there any recommended applications or platforms?

Dear researchers, In a systematic review (not a meta-analysis) compiling studies on various diagnostic systems against a specific pathogen. The most relevant parameters evaluated are the type of...

03 July 2024 9,069 3 View

What is the current usage and patronage of parks and greenspaces by older adults (aged 65+) in Salford? How does the frequency of older adults' visit?

What is the current usage and patronage of parks and greenspaces by older adults (aged 65+) in Salford? How does the frequency of older adults' visits to parks and greenspaces in Salford relate to...

22 June 2024 7,616 1 View

How can we compare SENTINEL vs LANDSAT for NDVI?

A question to see who can answer it. If the red and infrared bands of the satellites are...

16 June 2024 2,249 1 View

ImageJ Concentric Circles?

Hi there! We are trying to use the Concentric Circles Plugin on ImageJ to determine signal intensity in neurosphere cryosections after immunocytochemistry/confocal analysis. We determined the...

12 June 2024 7,332 0 View

How do i use researchgate to cunduct literature review ?

I am a first-time researcher in the field of nursing and i would like to conduct research about knowledge and attitude towards prevention and spread of tuberculosis.

11 June 2024 3,821 2 View

Is there any possibility for cultured mouse neurons more than 7 days?

Dear colleagues, I'm planning to start neuron mouse co-culture with astrocyte and microglia but I heard that it's difficult to keep it up. Any advices?

27 May 2024 4,905 3 View

What are some possible technical failures during lentiviral packaging using HEK293T?

I'm having trouble packaging lentivirus in HEK293T using pCMV, pMDG, an shRNA and polyfect. I normally seed 1.5 x 106 HEK293T cells in 60 mm on Day 0, which translates to about 60 to 70%...

20 May 2024 9,067 1 View

What is the minimum amount of liquid and beads I can use for bead-beating in a 2ml vial?

I am planning to extract DNA with QIAamp Mini DNA extraction kit (Qiagen) from DNA Shield microbiome preserved samples. My samples contain small amount of cell, so my goal is to reduce the loss of...

14 May 2024 2,291 2 View

Similar questions and discussions
How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

How to understand this crystallographic phenomenon of low temperature crystals in zeolite?

During low-temperature testing, new diffraction peaks that appear could be indicative of several phenomena. In one of our tests, we observed notable new peaks around 40° and 45° in a specific...

06 August 2024 726 3 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close