I want to know how to set block parameter of a matrix gain in a simulink model?

Samia Larbi @Samia_Larbi

01 January 2015 0 9K Report

I have a simulink model and I need to enter a matrix gain on it, how I can set the parameters of this block?

Badges
Science topic

More Samia Larbi's questions See All

How I can design a kalman program for estimatio process?

Regarding electric vehicles tire road forces estimation, how I can design a kalman program for estimatio process?

01 February 2016 5,528 3 View

How can I use a gain as a matrix gain in a MATLAB Simulink model?

I have built a simulink model where I needed to use a block gain as a matrix gain, when the model was runing an error apeared "error of dimension" so I want to know the format of setting matrix...

31 December 2014 9,182 3 View

What is the solution of an algebric loop error message in a simulink model?

I designed a vehicle model and when runing, an error message appear which:" Algebraic state in algebraic loop containing '....../Product23' computed at time 0 is Inf or NaN. There may be a...

01 February 2014 1,394 7 View

How can I correct a division by zero in a Simulink model?

The division by zero error appears in a product block. What is the solution to avoid this error?

31 December 2013 4,926 1 View

What is the solution for this problem?

Algebraic state in algebraic loop containing 'estimation_force/Subsystem6/Product33' computed at time 0 is Inf or NaN. There may be a singularity in the solution.

31 December 2013 1,972 1 View

How can I can correct an integrator error under MATLAB /Simulink ?

While running a Simulink model the error message appeared:"Derivative input 1 of 'md_3/Subsystem/Integrator1' at time 1.00003 is Inf or NaN. Stopping simulation. There may be a singularity in the...

11 December 2013 8,135 25 View

Any advice on implementing DTC control of a dual parallel PMSM?

I need to know how to implement the DTC model of a dual parallel PMSM used in an electric vehicle drive. Any suggestions?

10 November 2013 3,185 4 View

How to simulate an electric differential for a four in-wheels motor electric vehicle under matlab /simulink?

I need the model of the electric differential, I have conceived a model but it was not the required one.

09 October 2013 1,936 1 View

How to simulate a varying three-phase load /load profile in Simulink/MATLAB?

I have a Simulink model that connected a main utility (AC-grid) with a three-phase load changing from 20kW to 100kW in 5 seconds and I don't know how to build this load in Simulink. Please your...

14 July 2024 8,892 3 View

Dear Professor/Researcher, I want to use LoRa to send a signal with a frequency of 10 kHz. Is this feasible or not?

I use LoRa with Matlab/Simulink

23 June 2024 3,847 3 View

Aspen Adsorption linking to MATLab ??

Hi, I am looking to link MATLAB to Aspen Adsorption. I know that for Aspen Plus, it is possible to use actxserver(). Does anyone know if the same method can be used for Aspen Adsorption as well?...

20 June 2024 8,338 2 View

Does anyone know where this module is in Simulink?

I try to build a three-phase wireless power transmission model and saw this module in an article.

27 May 2024 3,471 2 View

Can you help me for do this matlab simulink project?

I'm new. I know just little use of matlab. Help me for do this matlab simulink project.

25 May 2024 4,247 1 View

Simulink model for ANC earmuffs?

Adaptive Filters are core of the ANC system. They continuously adjusts its filter coefficients to minimize the error signal, effectively generating the anti-noise signal. Common choices include...

21 April 2024 4,468 1 View

I need help designing an H Infinity controller to control a wind energy conversion system ?

What is the best approach to design an H infinity controller for a linear model of a wind energy conversion system, with the goal of simulating it in Simulink? Any specific methods or tools...

26 March 2024 4,008 1 View

Any suggestions to implement TECS on MatLab/Simulink?

Hi, I am trying to implement the TECS core algorithm to my closed-loop 3DoF model of the aircraft in MatLab/Simulink. The tuning of the innermost loops was accomplished succesfully, but now I am...

17 March 2024 8,446 1 View

Who has work on droop control for grid forming ??

could we make grid forming as stand alone inverter and control it by add active power ref and frequancy and voltage for rl load ? who has work on it in matlab simulink ? for me i did it for rl...

11 March 2024 6,303 0 View

Find a controller for a feedback-loop?

My team and I are working on an automation project to stabilize the altitude of an airplane. However, we've encountered an issue that seems unsolvable for us, at least for the moment, in the final...

03 March 2024 7,659 0 View