11 November 2013 4 3K Report

I need to know how to implement the DTC model of a dual parallel PMSM used in an electric vehicle drive. Any suggestions?

More Samia Larbi's questions See All
How I can design a kalman program for estimatio process?

Regarding electric vehicles tire road forces estimation, how I can design a kalman program for estimatio process?

01 February 2016 5,528 3 View

How can I use a gain as a matrix gain in a MATLAB Simulink model?

I have built a simulink model where I needed to use a block gain as a matrix gain, when the model was runing an error apeared "error of dimension" so I want to know the format of setting matrix...

31 December 2014 9,182 3 View

I want to know how to set block parameter of a matrix gain in a simulink model?

I have a simulink model and I need to enter a matrix gain on it, how I can set the parameters of this block?

31 December 2014 8,559 0 View

What is the solution of an algebric loop error message in a simulink model?

I designed a vehicle model and when runing, an error message appear which:" Algebraic state in algebraic loop containing '....../Product23' computed at time 0 is Inf or NaN. There may be a...

01 February 2014 1,394 7 View

How can I correct a division by zero in a Simulink model?

The division by zero error appears in a product block. What is the solution to avoid this error?

31 December 2013 4,926 1 View

What is the solution for this problem?

Algebraic state in algebraic loop containing 'estimation_force/Subsystem6/Product33' computed at time 0 is Inf or NaN. There may be a singularity in the solution.

31 December 2013 1,972 1 View

How can I can correct an integrator error under MATLAB /Simulink ?

While running a Simulink model the error message appeared:"Derivative input 1 of 'md_3/Subsystem/Integrator1' at time 1.00003 is Inf or NaN. Stopping simulation. There may be a singularity in the...

11 December 2013 8,135 25 View

How to simulate an electric differential for a four in-wheels motor electric vehicle under matlab /simulink?

I need the model of the electric differential, I have conceived a model but it was not the required one.

09 October 2013 1,936 1 View

Similar questions and discussions
Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

How does grain and grain boundary affect the ceramic when studying its dielectric properties?

I am not able to get good literature and the physics behind how first these grains and grain boundaries arises out of no where when we make a pellet to study its dielectric properties and then how...

07 August 2024 5,177 3 View

Is there any machine to do real time pcr?

I want to know how do you make real time pcr solation ? is there any machine to make it? thanks for answering

05 August 2024 1,660 0 View

Why is the molecule's orientation with an electric field affect polarizability?

Why is the molecule's orientation with an electric field affect polarizability? Electrons are diffuse enough to be independent with respect to orientation and effect of electric field on...

03 August 2024 7,843 1 View

In WECS : Gain values for conversion of PMSM rotor speed(rad/s) to p.u. input to wind turbine and Torque(pu) of WT to input of PMSM-Torque (Nm) ?

I am working on developing a MATLAB Simulink model of Wind turbine with PMSG followed by MPPT Boost converter. I have gone through so many literature and videos but I am not finding clear solution...

03 August 2024 888 1 View

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

29 July 2024 7,714 4 View

May I know the exact Quartile of the journal- Advanced Engineering Materials (Wiley) for material science category?

In some data sources it has been grouped in Q1 and some shows it is Q2.

29 July 2024 4,227 2 View

Ternary in Electrical Engineering?

Dear Research Community I would like to invite Elctrical Engineering specialists to solve problems related to Ternary Algebra or tripple sets I have an algorithm that places in relation three...

28 July 2024 5,771 2 View

Is it necessary to attach fluorophore at 3' end in MIC RT PCR machine for Dual hybridization Probe designed especially for genotyping assay?

I designed 2 dual hybridization probes for my single SNP. where I attach my fluorophore 5'-FAM-nnnn-BHQ1-3', and 5'-HEX-nnnnnn-BHQ2-3'. I need to run it on the MIC RT PCR machine by Biomolecular...

28 July 2024 5,658 0 View

How to conduct a sensitivity power analysis for Kendall's Tau?

Is there a straightforward way to conduct a sensitivity power analysis for a Kendall's Tau correlation? I was considering using the sensitivity setting and "Correlation: point biserial model" test...

28 July 2024 6,133 8 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close