How to simulate an electric differential for a four in-wheels motor electric vehicle under matlab /simulink?

Samia Larbi @Samia_Larbi

10 October 2013 1 2K Report

I need the model of the electric differential, I have conceived a model but it was not the required one.

Zol Bahri Razali

InsyAllah I will explain in detail soon.

Badges
Science topic

Similar topics
Engineering

More Samia Larbi's questions See All

How I can design a kalman program for estimatio process?

Regarding electric vehicles tire road forces estimation, how I can design a kalman program for estimatio process?

01 February 2016 5,528 3 View

How can I use a gain as a matrix gain in a MATLAB Simulink model?

I have built a simulink model where I needed to use a block gain as a matrix gain, when the model was runing an error apeared "error of dimension" so I want to know the format of setting matrix...

31 December 2014 9,182 3 View

I want to know how to set block parameter of a matrix gain in a simulink model?

I have a simulink model and I need to enter a matrix gain on it, how I can set the parameters of this block?

31 December 2014 8,559 0 View

What is the solution of an algebric loop error message in a simulink model?

I designed a vehicle model and when runing, an error message appear which:" Algebraic state in algebraic loop containing '....../Product23' computed at time 0 is Inf or NaN. There may be a...

01 February 2014 1,394 7 View

How can I correct a division by zero in a Simulink model?

The division by zero error appears in a product block. What is the solution to avoid this error?

31 December 2013 4,926 1 View

What is the solution for this problem?

Algebraic state in algebraic loop containing 'estimation_force/Subsystem6/Product33' computed at time 0 is Inf or NaN. There may be a singularity in the solution.

31 December 2013 1,972 1 View

How can I can correct an integrator error under MATLAB /Simulink ?

While running a Simulink model the error message appeared:"Derivative input 1 of 'md_3/Subsystem/Integrator1' at time 1.00003 is Inf or NaN. Stopping simulation. There may be a singularity in the...

11 December 2013 8,135 25 View

Any advice on implementing DTC control of a dual parallel PMSM?

I need to know how to implement the DTC model of a dual parallel PMSM used in an electric vehicle drive. Any suggestions?

10 November 2013 3,185 4 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

29 July 2024 7,714 4 View

May I know the exact Quartile of the journal- Advanced Engineering Materials (Wiley) for material science category?

In some data sources it has been grouped in Q1 and some shows it is Q2.

29 July 2024 4,227 2 View

Ternary in Electrical Engineering?

Dear Research Community I would like to invite Elctrical Engineering specialists to solve problems related to Ternary Algebra or tripple sets I have an algorithm that places in relation three...

28 July 2024 5,771 2 View

What topic or subject does Production Engineering need to address more?

Contemporary scores or innovations in scientific approaches. Hybrid methodologies, emerging themes and cross-cutting issues?

27 July 2024 648 3 View

Can a shoot-through event of a tri-state digital buffer cause momentary Hi-Z state?

// interested in the difference between floating events and short circuits.

22 July 2024 6,565 0 View

Is there a good macro photography kit for on-site metallurgical investigation?

I am looking to purchase a photography kit for onsite metallurgical investigations, such as capturing photos of worn areas, hot tears, cold tears etc. Could anyone suggest me a good...

22 July 2024 3,490 2 View

Why do fish have fishy odors naturally ?

Chemical Engineering /Food Engineering

20 July 2024 4,152 4 View

What could be the possible reason that sintering of polycrystalline diamond fabricated with tape casting has suddenly started failing?

I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...

16 July 2024 3,212 5 View

What should I upgrade in my computer to speed up simulation in CST?

I want to reduce simulation time in CST for frequency domain solver by upgrading my computer. I already have discrete GPU but it doesn't seem to make any difference at all compared to integreted...

10 July 2024 2,789 4 View