I want to ask about how to calculate reynolds number of a mixture

More Hemaizia Abd el Kader's questions See All

Could you recommend any books about Number Theory?

Beginner level books. High level books. Analytical Number Theory. Algebraic Number Theory. Combinatorical Number Theory. Books about partitions. Books about primes.

03 March 2021 7,174 5 View

What is the state of the drug inside solid lipid nanoparticles (SLNs)?

I am a little confuse with the mechanism of solid lipid nanoparticles (SLNs). The main point of encapsulating drugs into SLNs is because some drugs have low solubility in water. Therefore, SLNs...

01 March 2021 3,703 3 View

Why is the efficiency of viral mRNA electroporation in PBMC low?

Hello, I have been struggling with the electroporation of PBMC with HIV-I mRNA. Although the quality of the RNA generated is good, and the handling of the cells in meticulous, the frequency of...

27 February 2021 9,233 3 View

Have anyone checked before Cyclic voltammograms of intial ITO substrate and E-teck?

As a beginner in electrochemistry, I tried to obtain cyclic voltamograms of commercial anatase powder deposited on an ITO substrate or on Eteck. After several attempts, I noticed that my cyclic...

23 February 2021 3,175 3 View

The type of filter paper used to filter an epoxidized oil (the mixture is an epoxidized oil with magnesium sulfate) ?

I have a mixture of epoxidized oil and magnesium sulfate wich type of filtre paper should i use

21 February 2021 3,944 3 View

Any information about dinitrosalisylic acid reagent end point color stability ?

I work on estimation of alpha amylase activity using dinitrosalisylic acid reagent If i put the reagent to stope the enzymatic reaction and allow the reagent to react with the produced reducing...

17 February 2021 7,402 4 View

Is There are any idea to achieve H NMR signals for swollen compound ??

the samples are not completely soluble - just swelled the solvents that's mean the sample may be partially soluble any suggestion, please

16 February 2021 8,801 3 View

Is there association of SARS-CoV-2 infection rate with meteorological factors?

There are contradictory research papers about the correlation between meteorological parameters and incidence of COVID-19 in some countries worldwide. Is there correlation between the...

15 February 2021 5,806 2 View

Are there alternatives to the Devarda alloy when estimating nitrogen?

Are there alternatives to the Devarda alloy when estimating nitrogen? devarda alloy is reducing the nitrate to ammonium

15 February 2021 8,838 3 View

Can the viability assays (ex: MTT/CCK-8) measure cell proliferation? or are they solely viability assays?

I want to conduct a proliferation assay to test a chemotherapy combination on a cancer cell line. At first, I thought about the MTT assay. But now, all sources are saying that these do not measure...

14 February 2021 3,142 7 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

No title

I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...

25 February 2021 2,615 3 View

Modeling viscosity using model of Chung?

Hello, As part of simulation of gases mixture and water, I need to calculate viscosity of the fluid components and I am using relationships proposed by Chung et al. (1988). The irony is while I...

25 February 2021 8,053 5 View

What is the suitable range of Sulfur content and Viscosity of Heavy fluid Oil that used in Kiln?

What is the disadvantages of high sulfur content to the ceramic burning process? and what is the effect of outranged viscosity?

24 February 2021 8,219 2 View

How Can I clain a removal of a co-author?

I would like to make a correction in a co-author in your paper which is wrong. This name is also in other papers of Kenton Ko. Zey Ko is not a Co-author . The correct name is Zdenka...

24 February 2021 3,476 4 View

How does the injection volume impact LLOQ and ULOQ in regression analysis (LC-MSMS)?

Hello, I have run into an issue that has sparkled a debate at work: is the LLOQ/ULOQ impacted by injection volume under the following circumstances: 1) Same dilution factor of all samples 2)...

23 February 2021 9,159 3 View

Difficulty in debugging code to correct error - TypeError: '<' not supported ?

I am trying with a Unet code ontained from net ...in tensorflow. When trying to predict the segmentation result with the trained and saved model with metric " iou" using "CustomObjectScope"...

22 February 2021 5,254 1 View

How to perform Haldane correction on SPSS?

I was wondering if anyone knew how to perform the Haldane correction for SPSS (this is the definition of the correction -...

21 February 2021 2,882 1 View

How to determine number concentration of polymer solutions using viscosity experiment?

I have synthesized PNIPAM (Poly (N-isopropylacrylamide)) microgels, which are copolymerized with oligo-ethylene glycol based comonomers. I have to determine the exact number concentration for each...

19 February 2021 5,205 5 View

Rohit singh Gulia

Have you also used mixture velocity of propane-air mixture along side mean viscosity?

Hemaizia Abd el Kader

Hello Mr Rohit singh Gulia , I used the mixture velocity to calculate reynolds ( Re= axial_velocity*dh/Kinematic viscosity) but for the kinematic_viscosity just I interpolates it between two Temperature degree...

Is this method correct?

Chitrarth Lav

I think you should also factor in the volume/mass fraction of the components. Say, c represents the fraction of air, then 1-c is fraction of propane. The net viscosity could then by = c*mu_air + (1-c)*mu_propane.