Cell arrangement construction in center hole thermal battery?

how is the cell construction in center hole thermal battery.means what is the diameters of anode,cathode and heat pellets and separator.

31 December 2018 9,667 0 View

How to overcome friction between die wall and powder particle ?

we can't use any lubricant because here we can't use any liquid.

10 November 2018 867 4 View

What are the inorganic binder materials for powder metallurgy to produce uniform size after compaction?

we need binding material to produce uniform compaction and that binding materials will not produce gas.

08 September 2018 1,404 3 View

What is the suitable binder can be added to the iron powder to produce uniform in size and green strength?

we are working on thermal batteries in that we use different powders to make pellets.But the pellet is in not uniform and not green strength.what is the suitable binder can be added to the iron...

08 September 2018 847 0 View

By doing fusion to increase the powder quality?

after fusion the powder is in fine and it is produce uniform in size after compress the pellet.

08 September 2018 2,114 2 View

Optimum die design for powder compaction to get uniform pellets?

i need this information to get uniform pellets

08 September 2018 776 3 View

Actually we use single action pressing by using this press to get uniform thickness of the compact?

Our thickness range up to 1.5mm.is there machine or die problem to not get the uniform thickness or powder problem we are pressing manual and filling powder is also manual in die.tell me the...

08 September 2018 2,299 1 View

How much pressure is applied to make the pellet have green strength and achieve thickness upto 1 mm ?

we use weight 0.5 to 3 gr.In this range we have to get green strength and our thickness range is 0.1 to 1mm .in this range how much pressure is required to make the pellet is uniform

07 August 2018 5,082 1 View

What is the reason for not getting uniform pellets in hydraulic powder compaction pressing?

tell me that reason

07 August 2018 3,885 1 View

How much load should be applied for a making an pellet in uniform and green strength?

How to calculate pressure in powder compaction pressing by knowing of weight of material and thickness and diameter in theoritical.

07 August 2018 9,614 6 View

Looking for Materials with high thermal expansion coefficient and high temperature resistance?

03 March 2021 8,272 1 View

Research on Supply Chain Management in Indian context?

Hi, I am planning to apply for the PhD degree in the Supply Chain Mgt. with specific area of "Cold Storage warehouses" during Pandemics and wars. Where lock downs and shut downs are frequent....

02 March 2021 285 2 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

How to calculate the annealing temperature of a primer pair?

I have to amplify a gene and my primers just reached. The Tm for Forward primer is 64.2, and that of reverse primer is 65.5. Can some one suggest how to get the best annealing temperature? Thanks...

01 March 2021 360 7 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

PUC19 as a transfer plasmid for lentiviral delivery?

Hello, Is it possible to use pUC19 as a transfer vector to be packed in using the second generation viral particles packaging system( pMD2.G; psPAX2 plasmids)? As far as I understand it there is...

28 February 2021 4,868 2 View

Exit velocity of natural gas from pressurized tank?

Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...

26 February 2021 6,253 3 View

Why do the air flow results vary totally when adding scalar in CFD ?

Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...

25 February 2021 9,602 4 View