Cell arrangement construction in center hole thermal battery?

01 January 2019 0 10K Report

how is the cell construction in center hole thermal battery.means what is the diameters of anode,cathode and heat pellets and separator.

Badges
Science topic

More Durgam Raju's questions See All

I have one doubt in Heat transfer. If we keep the sealed container in a cold chamber of-50deg-centigrade at what time the inside temperature reaches ?

Please give answer to my question.

06 July 2019 1,616 3 View

How to overcome friction between die wall and powder particle ?

we can't use any lubricant because here we can't use any liquid.

10 November 2018 948 4 View

What are the inorganic binder materials for powder metallurgy to produce uniform size after compaction?

we need binding material to produce uniform compaction and that binding materials will not produce gas.

08 September 2018 1,486 3 View

What is the suitable binder can be added to the iron powder to produce uniform in size and green strength?

we are working on thermal batteries in that we use different powders to make pellets.But the pellet is in not uniform and not green strength.what is the suitable binder can be added to the iron...

08 September 2018 929 0 View

By doing fusion to increase the powder quality?

after fusion the powder is in fine and it is produce uniform in size after compress the pellet.

08 September 2018 2,197 2 View

Optimum die design for powder compaction to get uniform pellets?

i need this information to get uniform pellets

08 September 2018 889 3 View

Actually we use single action pressing by using this press to get uniform thickness of the compact?

Our thickness range up to 1.5mm.is there machine or die problem to not get the uniform thickness or powder problem we are pressing manual and filling powder is also manual in die.tell me the...

08 September 2018 2,383 1 View

How much pressure is applied to make the pellet have green strength and achieve thickness upto 1 mm ?

we use weight 0.5 to 3 gr.In this range we have to get green strength and our thickness range is 0.1 to 1mm .in this range how much pressure is required to make the pellet is uniform

07 August 2018 5,205 1 View

What is the reason for not getting uniform pellets in hydraulic powder compaction pressing?

tell me that reason

07 August 2018 4,009 1 View

How much load should be applied for a making an pellet in uniform and green strength?

How to calculate pressure in powder compaction pressing by knowing of weight of material and thickness and diameter in theoritical.

07 August 2018 9,779 6 View

What is the reason for current dropping in OER , LSV curve?

I tried four trials of the same Copper Phosphides sample in Alkaline medium ( 0.5M KOH) with Hg/HgO reference electrode and Pt as counter electrode. I used 0.001 V/s scan rate for first three...

10 August 2024 3,629 1 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Why does my protein refolded to beta sheet during thermal denaturation analysis?

Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...

06 August 2024 1,989 3 View

How to heat polymer for about 130° without oil bath ?

is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it

06 August 2024 947 1 View

What should I do with parameters that are not relate to my simulation in MyLake model?

I want to Estimate surface heat fluxes using MyLake, but I don't have all the initial values in model parameters section and other sections,is there a way?

04 August 2024 1,537 1 View

Binder for ZnO nanoparticles in graphite paste electrode?

I have been using paraffin, but the deposited ZnO still detach from electrode. What is the best binder to modify graphite paste electrode with ZnO nanoparticles?

03 August 2024 4,624 3 View

Why chloride turns into chlorine gas in a Downs cell?

I imagine the battery drives the graphite into a carbocation, then chloride is oxidized to donate the electron to the carbocation, but what pushes the lost electrons of chloride to be shared...

03 August 2024 5,384 0 View

Regarding a model for simulating battery charge and discharge, what do you consider to be high fidelity?

Regarding a model for simulating battery charge and discharge, what do you consider to be high fidelity? What is the acceptable percentage of error (regardless of the metric)? Could you suggest...

03 August 2024 5,358 0 View

Good day!! All, can anyone recommend the best battery related journals to download research articles please?

I am an Mphil research student and looking for high impact factor battery related journals to download and read research articles to improve my knowledge and get new ideas in the field of battery...

01 August 2024 6,516 2 View

How to find a reaction is reversible or irreversible in CV? How to know the number of electrons transfer?

My screen printed electrode CV is given here. For Nerstean one electron reaction the delta E value should be close to 57 mV and ration of Ic/Ia should be close to 1. I did CV of my screen printed...

30 July 2024 4,671 3 View