I am working on Rotating Disk Electrode (RDE) and I have below questions. Anyone can help to understand?

11 October 2023 1 10K Report

For RDE,

01. How to calculate the electron transfer number (n) from the Levich plot.

02. How to calculate the rate constant (k) for the kinetic current (jk) equation.

03. How to calculate the concentration of the catalyst on the electrode surface.

04. When calculating the limiting current density (jlim), which value we should use-average or specific one as we are getting different values for limiting current density.

Md. Enamul Hoq

Please read the following paper. I hope you will get some ideas.

Lazaridis, T., Stühmeier, B.M., Gasteiger, H.A. et al. Capabilities and limitations of rotating disk electrodes versus membrane electrode assemblies in the investigation of electrocatalysts. Nat Catal 5, 363–373 (2022). https://doi.org/10.1038/s41929-022-00776-5

Badges
Science topic

More Md Mohsin Patwary's questions See All

How to get onecolumn document from standard IEEE ACCESS LateX template?

I have prepared a manuscript in IEEE Latex template, but for some purpose, I need to prepare a word file as well (detailed format is not required). Compared to two column .tex file, one column...

02 March 2021 1,830 3 View

Is there any effect of different colours of light (white, red, yellow, blue etc.) on the rate of photosynthesis? If yes, why?

Light is inevitable for the process of photosynthesis reaction. Naturally sunlight plays the vital role for this process. Light may be of different colours like white, red, yellow, blue etc....

02 March 2021 7,890 2 View

How does Scientist/RG community evaluates a case study article and the impact of it on a researcher career?

An article that is published as a case study in the SJR listed journal. How much value is added to a researcher career? How it is evaluated by a scientific researcher/University admission...

02 March 2021 9,661 3 View

What kind of food stuff increase the potentiality of human brain?

There are different kinds of food stuffs which we intake daily according to our requirements. Carbohydrate, protein, fat, mineral, vitamin, water are mainly working for the growth and development...

01 March 2021 831 2 View

What is the difference between L1 and L2 regularization in machine learning?

L1 and L2 regularization

28 February 2021 4,187 3 View

How to add missing citation?

Dear colleagues, I have found that many authors have a concern regarding their missing citation in RG because often citation in RG is lower than google scholars. I also missed some citation...

26 February 2021 928 6 View

Can anyone suggest me the best way for Regression analysis of Accidents?

Dear Altruist, I want to make a regression analysis based on accident data. But I am not finding the necessary information about what type of regression is more applicable for analysis accident...

23 February 2021 9,956 3 View

How much cell pressure and back pressure should I apply to start for triaxial test for different types of soil?

We have recently purchased a triaxial test instrument (MATEST) for testing different types of soil. After installing software, we are facing a issue of saturation where the samples does not...

23 February 2021 7,194 4 View

How to assure whether a regression tree overfit or not by seeing bias-variance value of the model?

Lets consider a regression tree in which variance is 1.1065*e-10 and bias is 2.962e-13. Also the model RMSE on training set is 1.5e-5 and on training set is 1.2950e-5. Is the model is overfit or...

22 February 2021 7,755 2 View

How can I measure the surface interaction or surface interfacial chemistry between polishing abrasives and upper surface of substrate ?

I am working on polishing abrasives. I need to do few characterizations ? which can provide the on time surface chemistry of substrate with polishing abrasive during optical polishing. I would...

18 February 2021 5,319 3 View

Does any one know how i can prepare liver tissue with transmission electron microscope with good fixation?

i have problem in preparation of liver tissue with bad cell organelles and how i can adjust osmolarity

03 March 2021 8,890 1 View

I need to image mesoporous silica nanoparticles that are in ~100 nm size and do high resolution TEM to look at mesopores. what grids should I use?

Need to image mesoporous silica nanoparticles using the TEM. Also, need high resolution TEM images to see the mesoporous structure. Kindly suggest what kind of grids to use. Thanks, Shatadru

02 March 2021 1,787 2 View

Shall I skip the measurement model in SmartPLS?

Hello everyone, I had run a mediation model in SmartPLS using questionnaires that were already validated among my statistical population. A professor who edited my paper -though she is not...

01 March 2021 3,052 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

PUC19 as a transfer plasmid for lentiviral delivery?

Hello, Is it possible to use pUC19 as a transfer vector to be packed in using the second generation viral particles packaging system( pMD2.G; psPAX2 plasmids)? As far as I understand it there is...

28 February 2021 4,868 2 View

SEM or Multiple Regression for an analysis without Latent Variables?

Hello, I have three hypothesis to test, all with the same IV. I am testing if the effect of the IV on the first DV is mediated by awe. I am then measuring whether the effect of the IV on a...

26 February 2021 8,399 5 View

How to properly calculate the fluid solid heat transfer between polypropylene matrix and glass fiber in a porous medium?

I'm building a cfx model of thermoplastic pultrusion process on ansys and i have a doubt on how is the proper way to set this parameter in a porous medium

24 February 2021 1,915 1 View

How to clean up TEM grid with plasma cleaner?

I need to clean the hydrocarbon contamination on the carbon substrate of TEM grid. However, I heard that substrate could be broken by the powerful plasma. My substrate is pure carbon, with ~3nm,...

23 February 2021 3,262 5 View

Model Volume fraction and magnetic field applications of nanofluids in ANSYS?

Hi I am working recently on a project where I have to study how the thermal properties or heat transfer enhancement of nanofluids as the volume fraction changes, or if a magnetic field is applied...

22 February 2021 961 2 View