Does anyone use antinuclear antibody (ANA) and anti-Phospholipid antibody ELISA kit for Non Human Primate serum samples?

I am looking for anti-nuclear antibody (ANA) and anti-Phospholipid antibody ELISA kit for Non Human Primate serum samples. Any suggestions highly appreciated. Thank you.

28 February 2021 6,512 3 View

Treating Intermediate Variable in Linear Regression Analysis in SPSS?

While performing the Linear regression analysis in SPSS version 26.0.0. my intermediate/mediation variable goes to the excluded section. Please share your valuable suggestion "How to restrain the...

25 February 2021 4,591 5 View

How is Initial GDP measured ?

Dear All, I am working on estimating Debt-Growth Threshold but confused about some points. My questions are; - How do we calculate initial GDP Per Capita? Shall we do it in STATA or excel file?...

15 February 2021 2,677 2 View

Having trouble with qPCR amplification plots. My curve's never seem to reach a plateau. Any ideas?

The parameters of the curve all seem acceptable, typically reactions results are above 0.9852, -3.1 to -3.6 slope, and 90-110% reaction efficiency. The results seem to be what I would expect from...

04 February 2021 1,138 3 View

How can I get rid of the bubbles in the SBS membrane?

I used methylcyclohexane/ ethylcyclohexane / n-butyl acetate mixed solvent to dissolve thermoplastic SBS & terpene resin. The mixture is then poured onto a glass substrate. After solvent...

24 January 2021 8,306 3 View

Can anyone provide me a protocl of Native PAGE with the 30% terminal resolving gel concentraion?

I am separating the AuCNs, which are Au nanoclusters. I used the 3% stacking and 30% resolving polyacrylamide from the reference. Eachtime when the resolving gel is polymerizing, plenty of heat...

22 January 2021 8,522 3 View

After G actin polymerization and labelling I didn't got filaments. Why?

Purified G actin and got 42kda band and an additional band just below it. While performing G actin polymerization and labeling with rhodamine-phalloidin I didn't observe filaments under the...

20 January 2021 3,751 2 View

How to Import .inp file from abaqus CAE to Ansys perfectly?

I am trying to import an Abaqus .inp file to Ansys but it does not import the whole assembly but only imports a single part. How to solve this.

17 January 2021 5,450 3 View

Which one I should choose in Abaqus ?

Hello, plese give me your idea! I simulate one slab concrete affected by temperature at top and bottom surfaces. after that, have a static load distribution with small area put on top surface. I...

12 January 2021 5,769 4 View

No title

11 January 2021 3,284 3 View

What is the most Operating System (OS) which can be INSTALL on Tiny hard devices like Raspberry Pi (RPi) hardware ?

I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...

03 March 2021 1,931 5 View

High aspect ratio hexahedral mesh optimization solver?

I am interested in evaluating mesh optimization solvers that converge to high aspect ratio unstructured hexahedral grids. In other words, I am interested in a solver that optimizes warpage,...

26 February 2021 7,279 2 View

What could be the reason for not having further low chi square value (better agreement) in my refinement result?

I have tried every combination of parameter changes and after that i have a poor chi square value. I can't get it lower any further. I know there have been a lot of discussion about Rietveld...

26 February 2021 8,480 3 View

How do you mesh a thin solid in Fluent?

Hello, I have used the shell function on SpaceClaim to create thin solids for the model I am studying. These are contained within an enclosure for my study. I chose this approach as it avoids the...

24 February 2021 8,856 3 View

Why CHi^2 is reducing if I divide the intensity by a constant factor?

I was refining my XRD data in FullProf. Highest intensity was 400000. The fitting was good but still the Chi^2 value is very high (0.174E+04) I divided the intensity by some constant factor (say...

17 February 2021 3,383 5 View

How to mesh complex geometry?

I have been trying to mesh some complex geometry and have been having issues. I have attached images of the geometry in question. This structure is very large in size but has some comparatively...

05 February 2021 6,379 5 View

How to conduct mesh sensitivity/convergence analysis in MSC Marc Mentat?

Currently using Msc Marc Mentat for FEA. Now i conduct the mesh convergence/sensitivity analysis manually. So I need to know if there any automatic way to conduct the mesh convergence/sensitivity...

04 February 2021 3,310 3 View

Please recommend me the proper steps (blocking method) to generate Hexahedral mesh of the following geometry inside ICEM-CFD?

I am facing an issue while blocking for the geometry mentioned in the image. After blocking it ends with a triangular block due to its shape. How to create a hexahedral mesh for this geometry in...

02 February 2021 888 1 View

How do I refine a specific region of my protein model so that it perfectly superposes with a template peptide PDB with the same sequence?

I have a protein model and want to replace a 12-amino acids-long region within the center of the model with those of a PDB file containing a 12-amino acids long peptide of the same sequence. This...

02 February 2021 779 2 View

Is it possible to do Reitveld Refinement on single crystal XRD data?

I tried to do single-crystal Rietveld Refinement on my single-crystal XRD data using the option "refinement on single-crystal data/ integrated intensity data" in Fullprof but it is giving error...

30 January 2021 7,813 3 View