Heat a flat surface let say 1000mmby200mm with uniform temperature, is there any way to attain uniform temperature?
Sarvesh,
What is the surface made of and what temperature range are you looking to stabilize the surface at?
I've used metal foil-on-kapton successfully in the past to deliver uniform heating rates to plates: in the range of 140K to 300K.
Like these - applied to 300mm diameter 15mm thick aluminium discs.
https://www.alper.it/prodotti/scheda.asp?ID=4&lang=en
If the surface to be heated is non-uniform, or simply rather large, you may want discrete heating elements with local thermometers controlling the heating rate.
You can use a silicone rubber heater
One of my friends, every night after falling asleep, his mouth would make a creaking sound after chewing something. This teeth grinding condition would continue until he woke up, and he didn't...
08 August 2024 1,366 5 View
Hello all, I wanted to know, can I use galaxy (USA, Europe or Australia) platform for analyzing the shotgun data, and can it be used for publication purpose as well? Thanks :)
06 August 2024 6,610 4 View
i have sorted anti-NP specific plasma cells from bone marrow of C57BL/6 mice at certain times after immunization with variable counts and isolated total RNA using TRIZOL method for RT-PCR using...
05 August 2024 8,835 1 View
Nothing
01 August 2024 755 1 View
Dear All, I am trying to transfect a pCDNA3.1 vector containing my gene of interest. The purpose is to figure out the localization of the protein of interest. I have fused the protein with GFP on...
31 July 2024 9,892 4 View
The threshold voltage (Vth) of a MOS device plays a crucial role for its operation. At the same time, noise is an intrinsic factor. So how noise (flicker or thermal) change with the change in...
29 July 2024 3,246 0 View
In a research, lesion diameter due to a disease has a CV below 10%. However, in an another parameter, disease inhibition percentage (compared to control), a value derived from lesion diameter...
27 July 2024 201 0 View
Hi, can someone please help me with their expertise. To analyse a dataset with 2 IV´s (2 levels each) and 1 DV (time - measured at 4 points, i. e. 4 DV?) I found the two-way repeated measures...
24 July 2024 3,284 6 View
Hello everyone! Someone working with Crispr Cas9. I have a question. Is it possible to edit a gene that is present on a plasmid (in this case with a low copy number)? In this case, is it possible...
22 July 2024 7,073 2 View
How to determine tannin content in fodder pellets?
22 July 2024 8,163 3 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...
06 August 2024 1,989 3 View
is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it
06 August 2024 947 1 View
I want to Estimate surface heat fluxes using MyLake, but I don't have all the initial values in model parameters section and other sections,is there a way?
04 August 2024 1,537 1 View
We have a lateral flow test on Sartorius 140 NC. The conjugate is gold-monoclonal antibody. Using different control lines (GAM, protein A, protein G) we get a very strong leading edge with reduced...
31 July 2024 4,510 3 View
A computational study of heat flux on cylindrical surfaces using CNT hybrid nanofluids
28 July 2024 4,985 1 View
I would like to conduct artificial sunlight experiments to mimic heat capture and air warming in a greenhouse system. The main objective is to heat up the temperature inside the greenhouse, not...
28 July 2024 4,006 2 View
I am an undergraduate mechanical engineering student seeking suggestions on topics related to either thermodynamics, fluid mechanics, heat transfer or renewable energy for my final year project....
24 July 2024 4,058 5 View
I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...
16 July 2024 3,212 5 View
Hello everyone, I am facing a consistent issue in my NMR spectra with an unwanted peak appearing at 1.25 ppm. This peak seems to vary with the amount of sample: it becomes more pronounced with...
15 July 2024 9,065 4 View