The console window reads as :
Error: Build Grid: Aborted due to critical error.
Error Object: #f
It will be a great help if anyone has came across the same thing.
Thanks in advance.
If you have done any modifications like say you modified boundary conditions in the Setup... delete previous file and upload it again. Update the locations.
No I just opened a new fluent window and imported the mesh.
Can you elaborate what are 'locations'?
Thank you for your response
Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...
07 August 2024 1,937 1 View
How can we differentiate between calcite, dolomite, siderite, magnesite and ankerite minerals in carbonatite rocks in thin section under optical microscope?
07 August 2024 2,132 3 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
How to enhanced h-index in Research Gate?
04 August 2024 3,368 4 View
I want to do wavelet transform of some compounds for their comparative study? Kindly help me in this regard and provide with proper procedure.
31 July 2024 4,170 0 View
These days policy coordination is becoming necesssary on different front. In India also it is the same case. Monetary and Fiscal policy interface is important in order to address the...
30 July 2024 2,104 6 View
I am using CuBr/THPTA for a click reaction in total cell lysates. I am facing issues with my protein sample in non-reducing SDS-PAGE where it's not migrating properly and most of it remains at the...
29 July 2024 950 4 View
How to use energy flexibility in inventory modeling?
29 July 2024 2,192 5 View
Please send me updates regarding the above-mentioned areas in the question mark?
28 July 2024 5,197 3 View
Hi there, I did a CFA to 10 items on 2 latent variables. The model fit is too good and I've never seen it before. CFI / TLI = 1, RMSEA = 0. Is it okay, if everything else was done properly?...
24 July 2024 5,454 7 View
I am modelling CFS Sheath wall in abaqus and i am applying the 100 mm displacement but i am getting high reach force close to 150 kN but i need it till 50kN. I have used mesh independent fastner...
27 June 2024 4,212 2 View
For the article, I need some references for the subject of checking the convergence of the temperature field parameter for the SPH part in Abacus, and I want to study this case with a few meshes...
13 June 2024 2,504 0 View
Hello. I am trying to do contact-separation mode TENG. I have been following , and I am suffering to calculate the Open circuit voltage (Voc). I made geometry and set the materials setting all...
26 May 2024 2,645 0 View
Hi all, Here’s a simple but still very important (I think!) question regarding the philosophy of mesh overlap in open ventral hernia… I’m keen to clarify the concept of transverse diameter mesh...
25 May 2024 4,744 2 View
Hello I am trying to simulate 2dof cylinder for VIV analysis and I used an FDM method but the cd and cl values i got are so high and the damping is not coming into picture i tried and modified the...
17 April 2024 4,597 0 View
Dear Sir/ Ma'am When I am considering the human model with an antenna for simulation in CST then it is reflecting an error as "Time domain solver does not support mesh size > 2 billion mesh...
29 March 2024 8,205 1 View
1.Fixed boundary condition at both end of the pipe elbow. 2.Pressure applied is 30 Mpa. 3.Hex ,sweep mesh applied.
18 March 2024 5,935 2 View
I am currently conducting an analysis on a wind turbine and I am trying to input periodic boundary conditions in the mesh and it keeps showing me the same error which is the meshing algorithm...
13 March 2024 9,826 0 View
Greetings to all.. I am working on CFD analysis of a double pass solar air heater. The geometry is as shown in the attached file. It consists a rectangular duct with an absorber plate within the...
12 March 2024 6,154 0 View
There is a sealing with a rubber core and a polymer shell. The sealing is positioned into a groove and then is subjected to pressure from a one side. I've built a 2D model with plain strain...
26 February 2024 4,673 9 View