Hydrophobic coating by using SiO2 nanopowder

More Jai Ml's questions See All

What does an additional peak in FTIR between 3100 and 3300 nm affect the quality of the material, benzethonium chloride USP??

I do not know much about FTIR! The material Benzethonium Chloride USP was compared to a reference standard in regards to FTIR, as per the USP testing: Identification B. Infrared absorption (FTIR),...

16 July 2024 6,918 7 View

How to do protein quantification for western blot?

I am doing western blots for extracellular vesicle protein and I don't have a good loading control. I want to quantify my western blots to compare the amount of CD81 in EVs collected from two...

22 February 2024 9,876 2 View

Baseline trace element concentrations in soils - India, Nepal, Bangladesh/South Asia?

Dear all, Where can I find the baseline trace element concentrations in soils for South Asia esp. India, Nepal and Bangladesh? I have gone through papers like McLennan et al., 2001; Taylor &...

18 August 2023 4,166 0 View

How to find the data for the baseline trace elements concentrations for India?

Does anyone know how to access the data of the geochemical maps of trace elements listed in this paper? The relevant authorities are not responding to emails and calls and there is no data given...

05 June 2023 6,249 2 View

Where can I buy polyethylene microplastic with the particle size ranging from 1 um to 5 um?

Preferably, in the Philippines.

11 April 2023 1,740 2 View

Are researchgate preprints indexed in google scholar?

And if so, are they used to compute google scholar's citation indices for researchers?

17 March 2023 8,719 1 View

Is there any constraint to the power value of the Reynolds & Prandtl number in a correlation to evaluate the Nusselt number for nanofluid experiments?

I performed forced convection experiments with nanofluids (DI Water as base fluid) through different shaped flow sections, thus obtaining 432 Nusselt number and friction factor data. As known,...

27 October 2022 7,323 3 View

Can I have outline classification of yeasts?

I need this to teach Master's student

23 December 2021 4,636 13 View

Cylindrical-shaped diode on Sentaurus simulation doesn't converge?

I'm trying to simulate breakdown voltage characteristics of 2D Silicon PIN diodes in cylindrical-shaped diode. I've used cylindrical keyword (Yaxis=0) in the Math section in Sentaurus Device in...

12 September 2021 9,815 4 View

How do I run PHONOPY on output of VASP Virtual Crystal Approximation (VCA) Density Functional Perturbation Theory (DFPT) job?

I have a DFPT job (IBRION=8) run on VASP with the Virtual Crystal Approximation (VCA) method turned on. The system is 80at.% Ti, 20at.% V. INCAR and vasprun (files attached). Typically I use...

21 June 2021 5,364 0 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

What is the reason I get 400nm nanoparticles using an extruder with 200 nm membrane for cell membrane coating?

I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...

30 July 2024 3,294 3 View

What is the main used curing agent for epoxy based coating?

I am trying to coating metal oxide into steel substrate, for better sticking planning to utilse epoxy based, Could you please suggest suitable curing agent for the coating purpose

25 July 2024 438 3 View

How do you get pure primary macrophage cell culture?

I have been harvesting monocyte-derived macrophages from buffalo and cattle fresh whole blood using the same protocol for years and getting good macrophage cultures. Below is the protocol that I...

23 July 2024 4,074 2 View

How to decrease hydrophobicity of Ni-foam?

As, my studies are related to water adsorption, the substrates should be hydrophilic in nature. Ni-foam being hydrophobic in nature, the results are not as expected as in literature. Hence i...

14 July 2024 8,847 4 View

Issues in coating of cathode material on Al foil, why we are not getting proper coating and results when the cathode was coated on Al-foil..?

We are trying to coat some cathode materials on Al-foil ( ex - LiFePO4 , S@CNT, etc). When we coated the Al foil with the cathode (ex - S@CNT) material , the cycling result was annoying. But the...

09 July 2024 5,123 4 View

Can some indicate a technique - or approach - to measure the thickness of a 20µm film and thickness with water uptake?

Hi, I need to measure the real-time (or temporal intervals) thickness variation of a transparent material from dry to wet/humid conditions, however, I cannot use the following techniques: -...

08 July 2024 4,799 4 View

Why NCM cathode slurry has coating problem?

I tried to make slurry for NCM cathode but there was problem in coating process. The detail of my experiment is following; The ratio between active material(NCM811), conductive additives(Super-P)...

08 July 2024 7,327 4 View

Poonam Kharangarh

I think, you can try CVD and Sol gel Methods. Please find the attachments

Rajiv .S

So many research papers are available to prepare hydrophobic coatings. I hope this given links help you.

https://www.osti.gov/pages/servlets/purl/1185439

https://pdfs.semanticscholar.org/d6fd/a8af7133dcaf5dae7fe108b4fbd1c1c4b11b.pdf

Olga Proskurina

Hello! You can try to use a sol-gel method with MTEOS as a precursor and SiO2. But you will receive a translucent coating