How we can keep steel tube specimen freeze at -40 degree Celsius at room temperature for a hours?

More Amol Bhanage's questions See All

How Flexural Modulus calculated for Steel Tube, under three Point Bending Test?

Elastic Modulus for Steel Tube

31 December 2017 1,954 0 View

How Fatigue analysis for composite materials solved by using FEA Software? Suggest suitable software with case study

05 June 2017 7,568 3 View

For doing FEA fatigue analysis which software will be suitable for this analysis ? Any recommendation . Please also looking for same case study

Interested in doing fatigue analysis for composite materials ?

04 May 2017 4,024 8 View

On What basis, the fatigue testing of materials will be decide stress life or strain life approach?

should understand properly stress life or strain life approach

01 February 2017 2,750 0 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can formaldehyd-fixed gelatin be melt?

I am puzzled about the properties of gelatin, when used for tissue-embedding. Hard gelatin can be melt again by temperatures about 40°C. Formalin-fixed gelatin is like crosslinked protein and...

07 August 2024 1,686 1 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Melt curve problem in qPCR?

Do these peaks in the curve indicate primer dimer or non-specific products?

01 August 2024 7,466 0 View

What is the best protocol for freezing the rat brain in preparation for protein detection by Elisa ?

What is the best way to freeze the rat brain - liquid nitrogen, Dry ice , isopentane - after isolation for later protein investigation by Elisa?

01 August 2024 1,722 1 View

How to Post-fix Mice pup's brains?

I need to Postfix mice brains. I slice the brains using microtome at 40 microns. These are Postnatal days 7, 11, 14, and 21. I am using half the brain for other analysis, so I need to fresh freeze...

31 July 2024 1,123 4 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

Please investigate the effect of temperature and strain rate of hot deformation and the formation of delta ferrite in martensitic stainless steel 410?

25 July 2024 9,408 0 View

How to saturate steel samples with hydrogen?

I have tried to saturate ferritic steel with hydrogen using the electrolytic method and H2SO4. However, the effect was very poor even after 3 days of "saturation". Can anybody help in choosing a...

24 July 2024 4,393 2 View

Jumaa Salman Chiad

This link may help you

www.dlolab.com/.../PDFs/Go_Kit_Jun2017_specimen%20collection....

Amol Bhanage

Thanks for your reply Sir. But after click on link following error shown

ERROR

Main Content

The page you are looking for has been removed or has moved to another location. Please visit the home page or the site map.

Jyoti Vimal

The material that you measure are quite stable.