How to perform SEM and to include control variables in model?
Are categorical variables (like gender etc) included as it is in SMM (AMOS) or to use dummy variables when using these variables as control variables?
Specifically, I want to know that How the theoretical and then empirical contribution should be written for a research paper? Recently, I have been given the comments theoretical contribution(s)...
02 March 2018 2,094 3 View
I am collecting data for two levels: Departmetal Level (level) 2 and individual employee level (Level 1). I just wanted to know that how much no of observations are atleast required at level 1...
11 December 2016 7,942 7 View
What are the assumption to be tested before analyzing data for multi level analysis like HLM etc??
05 June 2016 5,810 1 View
What are the assumption that are required to be tested while before analyzing data in AMOS for CFA or structural equational modeling (SEM)??
05 June 2016 3,053 0 View
How to choose fixed and/ or random effect in HLM software?
05 June 2016 4,858 1 View
What is fixed effect model and random effect model and when to use fixed effect and when random effect???
05 June 2016 4,900 1 View
As a case, there are 6000 organizations and in each organization there are employees ranging from 7 to 50. I need to select samples from this population, At level 2, organizations, I have randomly...
05 June 2016 7,817 0 View
Please guide that what are the values in outcome files to use as model significance in multilevel modeling?
05 June 2016 2,061 0 View
how ICC1 and ICC2 are different and how to calculate ICC2 Purpose of ICC2 and cutpoints of ICC1 and ICC2?
05 June 2016 3,744 0 View
Can anyone please guide that when doing multi level data analysis, what the values in output file say? Also the interpretations of the data analysis of Multi level modeling
05 June 2016 4,790 2 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
Articles on" Gender disparities i leatherwork education"
07 August 2024 2,500 0 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...
05 August 2024 3,665 0 View
I have tried several times to isolate lymphocytes from mouse spleen, but all attempts have been unsuccessful. I tried most available protocols. I used different dissociation media (HBSS with Ca...
04 August 2024 9,913 7 View