03 March 2024 1 8K Report

Hi I am trying to simulate the crack propagation in 3 point bending by using Phase-field cohesive zone method, but I always have a convergence issue at 0.046s. Could you please help me?

Here are some settings.

More Zhuoyuan Leng's questions See All
How to I proceed for frequentist network meta-analysis after using reducing weights approach?

Dear colleagues, I am planning to conduct a random effects frequentist network meta-analysis based on continuous outcomes. As my samples has split-mouth and multi arm trials, I have implemented...

11 February 2020 9,919 2 View

Is placebo + active control still considered a placebo? which arm to include in pairwise meta-analysis?

Hi, I would like to ask whether a placebo + active control arm is still considered a placebo. In dentistry, scaling and root planing is considered an active control. There are studies especially...

07 January 2020 8,384 1 View

Is it typical to use CTT and IRT in testing the psychometric of a scale or one over the other?

My supervisor has suggested to use IRT after a long discussion around using CTT. I am confused as to ask whether to use both or one or the other. If I were to choose IRT only, which model should...

11 September 2018 5,469 11 View

Would anyone like to take part in my study?

It's a short, 10 minutes, online questionnaire guaging readiness for employment. It's designed for people with personality disorders, however anyone can take part as I am testing the psychometric...

24 July 2018 2,567 13 View

What can experimental groupings be considered reasonable?

Hello, everybody. There is a question about experimental groupings: the concentrations about 0, 0.5, 1.0, 2.0 is ok, and 0, 0.25, 0.5, 1.0 too. But how about 0, 0.05, 0.25, 0.5? In other word,...

15 May 2018 9,597 3 View

Hi, I am developing an Employment Scale for people with PD, do I have to run an EFA/CFA on non-clinical samples first?

I am struggling to find references for testing structural validity of a scale on non-clinical samples first, before running an EFA and CFA on people with personality disorders. I was told this is...

01 January 1970 5,071 2 View

Similar questions and discussions
Is there any tutorial for comsol general projections?

Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...

02 March 2021 4,624 4 View

Is it possible to do piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch?

How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...

02 March 2021 9,833 3 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

How to improve and implement WBAN MAC and Radio modules under Castalia 3.2 ?

Hello researchers, Hello Castalia3.2 researchers I am a beginner with Castalia, I work on optimization of RFID systems used in wireless body networks. I simulated a WBAN with 10 nodes and one...

28 February 2021 400 1 View

How to use measure capacitance change in COMSOL time dependent study ?

I want to measure change of capacitance due to relative displacement between two parallel plates in COMSOL. Distance between two plates changes with time. So I'm using a time dependent study but...

26 February 2021 8,567 3 View

Error in comsol?

Dear respected researchers, while performing CFD analysis in Comsol it's showing like this Error: Nonlinear solver did not converge. The maximum number of Newton iterations reached can...

24 February 2021 249 3 View

D2D implementation in Matlab in Vienna LTE software?

Hi Hope you are well. Can you please share your code for D2D implementation in Matlab. I want to implement D2D in Matlab based Vienna simulator and struggling to deploy D2D. Thanks

24 February 2021 9,378 3 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View

Is it possible to set a breakpoint at a specific DYNAMIC instruction using the GNU Debugger (GDB)?

Using GDB, it is straightforward to debug and monitor a target program by setting a break-point at a specific instruction, since the instruction addresses are known. However, we have two...

24 February 2021 1,598 2 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close