How does SEA software normally number subsystems?

Dear colleagues, What is the common subsystem numbering system in SEA modelling software (i.e. VA One, AutoSEA2)? Cheers, Feng

27 February 2021 7,073 3 View

How to remove the species data from rda data frame in R (only remain the sites/samples point)?

Dear everyone, When I using the rda function in r, I met this question. As you can see in the figure, there are a lot of deep blue points which refers to the species. But I would like remain...

15 February 2021 8,982 2 View

Western blot with very acidic proteins, any suggestions?

I am trying to do a Western Blot to detect acidic proteins (~30kDa) that have a PI of ~3.5, due to the presence of Asp and Glu repeats. The proteins are about 80% pure. After I ran them on...

24 January 2021 7,226 3 View

How to Extract DNA from dried rhizomes, wood, galls etc. stored for a long time?

Dear Respectable Scientists, I have been trying to extract DNA from above mentioned sources using different CTAB/SDS Buffer Compositions and purifying agents but I am not able to extract DNA from...

12 January 2021 5,899 8 View

Find value of heat transfer coefficient in SI units??

A tube is subjected to air at standard temperature and pressure conditions with velocity 5 m/s. initial temperature of the tube is 980 K and drops to 500 K after interaction with the cool air....

21 December 2020 6,408 3 View

Problems with allele speration by cloning in pKS plasmid?

I am trying to do the allelic separation of a ~8 kb region using cloning strategy with pKS plasmid. However, when I analyze the result of the colony PCR sequencing It seems that both alleles were...

14 December 2020 5,829 2 View

May I use Minimal important difference (MID) in non-normal distribution?

MID is based on Standard deviation, consequently, I should not use it in non-normal distribution. Am I right? If yes, which test may replace MID?

13 December 2020 7,573 3 View

Lyophilization problem related to Bacteria derived Gold Nanoparticles?

Respected Dr Yuri and Rawle We have prepared the bacteria derived gold nanoparticles and for its antibacterial and antioxidant applications we want exact concentration and for that purpose we...

25 November 2020 2,565 3 View

At what concentration does hydrogen peroxide inhibit enzyme activity?

I am trying to measure GUS expression, and was wondering if anyone knew what concentration hydrogen peroxide inhibits the GUS protein??? Thanks ! Any help is appreciated!

23 November 2020 4,101 3 View

How to determine additional cycle numbers using qPCR in ATAC-Seq?

I am doing ATAC-Seq with OMNI-ATAC-Seq protocol (Kaestner Lab 2019). I did PCR amplification for 5 cycles of my library. Now I use 5ul of the PCR product to do a qPCR to determine how many...

12 November 2020 3,678 1 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

Do anyone here can help us in the field of molecular docking?

We have synthesized various metal complexes with different environment around the metals. Now to see the application of synthesized complexes we need this study also. we are also interested in...

01 March 2021 1,899 2 View

What is the difference between genotype and haplotype data in the ped format?

Hi everybody In the ped format for genotype, alleles of any SNP are represented by two columns (one for each allele, separated by a space). Is a column sufficient for the haplotype to...

27 February 2021 1,965 1 View