How to solve distortion error in abaqus?

11 March 2023 0 3K Report

Hi. Dear any Abaqus experts who have modelled composites machining, could you kindly help me on this issue?

The elements contained in element set ErrElemExcessDistortion-Step1 have distorted excessively. It can be seen that the matrix overlaps with one of the circular particles, which causes this issue. In other cases, the matrix overlaps other areas of the matrix it self. Do you happen to know why and how to solve this issue? Thank you.

Badges
Science method

Similar topics
Biological Science
Ecology

More Edo Suryo Pratomo's questions See All

How to quantify lung fibrosis using ImageJ?

Hi everyone, I am currently working on lung fibrosis research on rat models of interstitial lung disease, I have problems with quantification of lung fibrosis on ImageJ. I used Masson trichrome...

01 April 2023 9,315 2 View

How are the researchers from ASEAN countries who are doing research relevant to Covid-19 stigma?

I would like to know our fellow researcher from ASEAN countries who are currently or in the past doing research relevant to the stigma of Covid-19

01 July 2020 4,728 2 View

What is the effect of the Covid19 pandemic to deposit interest rate and repo rate of the Asian central banks?

Currently almost every industry gets affected by the nCov2 pandemic. Economic activity as a whole is severely disrupted with the temporary closure of businesses, slowing consumption by consumer...

05 May 2020 6,956 5 View

What is the best telomerase activity assay for human whole blood?

Hi to everyone, I would like to check telomerase activity in the samples of my study. I have been checking the different methods and I found there are so many. Has anybody already done this in...

30 April 2019 2,491 3 View

How to purify RNA from human peripheral blood in Tempus™ Blood RNA Tubes using MagMAX™ for Stabilized Blood Tubes RNA Isolation Kit?

I have collected blood in Tempus™ Blood RNA Tube from Thermofisher to purify RNA and do whole RNA sequencing later on. After trying different kits and getting very low yield, I went for the...

10 September 2018 4,587 2 View

I am doing research about Pesticide detection device with a certain wavelength. What spectroscopy will give the best result ? around what wavelength?

Many Researcher using raman spectroscopy but i dont know why. And my research is not that Advanced just need to be able to detect 2 or 3 pesticides that many people use. And maybe if i can tell...

18 October 2017 2,263 4 View

Are you looking at xenobiotics and contaminants of emerging concern in recycled water as used for growing salad crops consumed raw?

Water is becoming an increasingly scarce resource. Oil-field frac water has now been used to grow Bermuda grass. Recycled wastewater, as a broad class, is being converted to drinking water as well...

15 February 2017 9,730 2 View

How do I calculate HHV of syngas using its mass?

I found this equation below from a research: HHV (syngas) = { HHV (H2) + HHV (CH4) + HHV (CO) } x m (syngas) I have a doubt about the equation because there is no citation that referred to it....

01 December 2016 2,096 5 View

I found equations in http://dx.doi.org/10.1016/j.apenergy.2013.01.034. Is it allowed to change mass flow rate in CC & CGE with syngas & fuel mass?

I am an undergraduate student of mechanical engineering and my final research project is to produce hydrogen with SCWG method. I get confused to calculate the Carbon Conversion and Cold Gas...

25 November 2016 1,571 3 View

Can someone suggest a pH 3-4 buffer system for yeast shake flask culture?

In bioreactors, I maintain a low pH via combination of cell metabolism and base addition. In shake flask, base addition is not possible, and I've been looking for a suitable, biologically...

02 September 2015 1,694 6 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,831 4 View

Is it true that $\det(V(A))$ may be only $\pm 1$, depending on $n$, for the last symmetric tridiagonal matrix $A$?

One can try to generalize the Vandermonde determinant in the following direction: Let $A$ be any symmetric $n$-order square matrix. Consider its powers' diagonal elements $(A^k)_{ii}$ and...

08 August 2024 6,690 1 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

Usage of internal standards in LC-MS/MS analysis?

Have you ever seen a LC-MS/MS method uses both internal standards and external standards (in matrix matching purpose) but the concentrations of internal standards are outside the calibration curve...

05 August 2024 3,084 6 View

Request a single Lecture notes for math as detailed as this that I can find in one place?

- The Existence/Uniqueness of Solutions to Higher Order Linear Differential Equations - Higher Order Homogenous Differential Equations - Wronskian Determinants of $n$ Functions - Wronskian...

03 August 2024 2,366 0 View

Tissue homogenization in mouse with FastPrep-24™ 5G - is the D matrix system useful?

I need to lyse and homogenise mouse tissues. So far I have experimented with liver and lung tissue, using matrix D. The liver was completely lysed with 6 repetitions of the standard program, but...

31 July 2024 9,186 0 View

Is it true that science is leaving the era of mathematics and entering the era of matrix mechanics?

We assume this to be true. Science leaves the era of mathematics and enters the era of matrix mechanics and the turning point is the discovery of numerical statistical theory called Cairo...

31 July 2024 3,900 2 View

Help on understanding the implementation of Mori Tanaka method on MATLAB?

I am new to Micromechanics and having similar problem with understanding the implementation of the formula's. I would appreciate if anyone can guide me on how to go about getting a scalar value...

30 July 2024 969 0 View