How to simulate the moving heat source on CFRP Laminates in ABAQUS?

08 August 2016 0 2K Report

I want to simulate the moving heat source on CFRP Laminates in ABAQUS. Can anyone help me in this regard?

Badges
Science topic

More Prakash Rajendran's questions See All

Can anyone suggest me an economic laser vibrometer which can measure the accurate mode shapes of the simple structure?

I wish to buy a economic (cost effective) laser vibrometer to measure the precise mode shapes of the structure. Can anyone suggest me other than polytec laser vibrometer.

10 November 2017 7,532 4 View

Does anyone have MATLAB Code for shearlet Transform?

I need a MATLAB code for shearlet transform to perform the analysis of tilted features in images.

07 August 2017 2,555 5 View

How to solve fourth order ODE equations numerically?

Can anyone explain me how to solve fourth order ODE equations numerically? or help me in solving the equation in MAPLE software. Thanks in advance...

06 July 2017 8,595 1 View

What is the expression for torsion vibration of thin plates?

I want to calculate shear modulus 'G' through the vibration method. Once I get natural frequency corresponding to torsional mode then I'll use it for the expression in order to find G.

09 October 2014 4,074 7 View

How does one give bidirectional woven ply orientation in ABAQUS?

For example , a ply has 0 and 90 orientations, so how to give these orientations in ABAQUS software.

07 August 2014 2,271 4 View

Is there any authenticate website to know about Impact factors of the engineering journals?

I know some website such as www.scimagojr.com, www.jifactor.com. But I would like to know about others website if it is available.

07 August 2014 1,343 2 View

How can I check the closeness of normal distribution?

I have data points that I want to check the closeness of normal distribution. So I can use ''hist'' function in MATLAB, but I need a coefficient which tells how closeness to the normal...

03 April 2014 1,620 13 View

Can I use six sigma method as threshold value for damage identification problems?

Is there any standard practices are available to use threshold value in the damage identification problems. If anything is there, kindly let me know.

02 March 2014 9,355 5 View

How do you avoid edge effects in wavelet transform?

I have a signal I would like to pass through the WT. I am very much interested in detecting the singularity in the signal but I found peaks at the edge.

02 March 2014 8,233 3 View

How to get reliable natural frequency when I repeat the vibration test for several times?

Basically, I am trying to detect damage on beam structures for a cantilever support. Suppose, I am measuring first natural frequencies from the experiments at several times of undamaged state of...

01 February 2014 2,217 6 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,831 4 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Why does my protein refolded to beta sheet during thermal denaturation analysis?

Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...

06 August 2024 1,988 3 View

How to heat polymer for about 130° without oil bath ?

is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it

06 August 2024 947 1 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What should I do with parameters that are not relate to my simulation in MyLake model?

I want to Estimate surface heat fluxes using MyLake, but I don't have all the initial values in model parameters section and other sections,is there a way?

04 August 2024 1,536 1 View

When I simulate for S parameters using ADS, I have faced this issue that I have attached. Please anyone clarify me?

...

31 July 2024 1,671 3 View

Simulation of metal drawing by Abaqus with UMAT?

Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...

30 July 2024 7,062 1 View

Why running a restart analysis in Abaqus in Ubuntu OS gives an error as attached when running the same job in Windows doesn't give any error and runs?

I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...

29 July 2024 9,572 3 View

What are the perfect mathematical model for a solar-powered ship implementation?

A computational study of heat flux on cylindrical surfaces using CNT hybrid nanofluids

28 July 2024 4,985 1 View