How can we measure dimensions of a molten pool in ANSYS APDL or WORKBENCH?

I am performing a thermal simulation using ANSYS in which the melt pool is simulated. I would like to measure the dimensions of melt pool. Is there any way to measure it? If any please help me...

02 March 2019 4,064 4 View

How to interface MATLAB with ANSYS APDL?

I need to extract data from MATLAB and give it as input in ANSYS APDL. Can someone tell me how to do it?

08 September 2018 7,234 2 View

In ANSYS APDL, what is the way to iteratively change a user defined variable in a function using a subroutine?

I have defined a function in function editor comprising of some constant values and a variable. I would like to change the values of variable in an iterative way by defining a subroutine. But...

06 July 2018 2,282 0 View

Can heat flux and convection can be applied on the same area in ANSYS APDL?

I want to apply heat flux and convection on the same area. But when i try to apply i am getting a WARNING message as "OVERRIDE". I have attached that warning message. Please help me out with this...

02 March 2018 7,401 3 View

How to perform simulation in ANSYS to naturally cool down a metallic substrate from high temperature to room temperature?

01 February 2017 8,524 0 View

How to perform thermo mechanical simulation for a laser metal deposition process using ANSYS?

Help me out with the option available in ANSYS which exactly suits for simulation of directed energy deposition process.

01 February 2017 6,082 5 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Which is the most convenient manufacturing software for Additive Manufacturing?

Which tools can be used to generate machine codes for additive manufacturing?

02 March 2021 7,220 2 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View