How to prepare bacterial Culture for SEM and TEM analysis ?

More Jagdish Parihar's questions See All

How to identify predatory journals ? and are all Scopus indexed journals are authentic ? Please provide authentic source to check ?

How to identify it ?

04 May 2019 8,516 5 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

Why Do TDS and EC Increase with Larger Wastewater Volumes, While BOD and COD Decrease?

I have carried out MFC experiments on three different volumes, 50, 500 and 1000 mL of wastewater. Results after MFC treatment shows that TDS and EC are more in larger volumes of water i.e. TDS and...

09 August 2024 9,621 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Could it be a cell culture contamination?

Hello everyone! I observed in my culture (htert-RPE1 cells) an orange- red particle at the bottom of the dish. It is visible to the naked eye as a very very small red dot. Could it be a...

09 August 2024 2,824 3 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

1. If I can quantize the atom using this hyperbolic spiral and classical physics, could nature do the same?

If we map as a continuous motion an ionising electron (beginning its journey at n=1) in an H atom, a specific hyperbolic spiral appears (see animation). When we solve this spiral formula, we find...

07 August 2024 5,343 2 View

Is there any way to quantify bacterial and fungal cells in their mixed culture?

I am working in fungal fermentation of soybean meal and there is bacterial growth in them at times. I am trying to quantify fungal cell counts and bacterial cells; but I haven't been able to do at...

07 August 2024 7,535 4 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

Muhammad Ismail Popular answer

Nirmla devi

Hello sir,

Please check below the previous RG discussion regarding the preparation of bacterial cultural for SEM analysis:-

https://www.researchgate.net/post/What_is_the_protocol_for_bacterial_sample_preparation_for_SEM_analysis https://www.researchgate.net/post/How_to_prepare_sample_for_SEM_of_bacteria_with_and_without_nanoparticles2

Muhammad Ismail

Michał Kulus

For TEM you may consider the methodology mentioned in this article:

Article Antlerogenic stem cells: Molecular features and potential in...

It was used for eukaryotic cells, but should work also for bacteria.