How to plot sputter yield vs target voltage?

13 August 2024 0 9K Report

I run simulations on srim software and I need to plot the sputter yield vs. target voltage

Badges
Science topic

More Hichem Bougherira's questions See All

How to achieve fibers during electrospinning? We are only getting electrospray. Can anyone help?

We are using a handheld spincoating system for wound dressing from the brand SpinCare™ (nanomedic.com). The instrument has fixed features that we cannot change. Basically, the voltage is fixed...

17 December 2023 2,994 3 View

About the strong commutativity of unbounded self-adjoint operators?

Let $A$ and $B$ be two unbounded self-adjoint (+ positive if needed) operators with domains $D(A)$ and $D(B)$ respectively. By the spectral theorem, we know that $A=\int_{\mathbb{R}}\lambda dE$...

06 September 2023 5,276 0 View

I want to know how to calculate curvatures vector with finite element method in composite materials ?

Noting that i'm using 4 nodes quadrilaterlal linear elements and i have nodal displacements.

17 April 2023 1,731 2 View

How to identify the composition of an unknown polymer blend solution?

We are looking for a way to identify the composition of a polymer blend that we do not know the composition. The composition is based on a polyurethan polymer, silicone elastomer, polyester-based...

27 December 2022 4,730 7 View

TYPE TRNSYS of vacuum thermal solar collector with PCM ?

Dear all, I would like to know what type of trnsys that allows to make a simulation of an vacuum thermal solar collector with PCM. Thanks, Best regards

26 April 2022 7,964 1 View

Is $TT^$ (or $T^T$) densely defined if $T$ is densely defined and symmetric?

Is $TT^*$ (or $T^*T$) densely defined if $T$ is a densely defined and symmetric linear operator? I feel this is untrue, but do you have a counterexample? Thanks, Hichem

16 February 2022 6,706 12 View

About an unbounded normal product of one symmetric operator and one bounded positive operator?

Let $A$ be a densely defined symmetric (unclosed) operator and let $B\in B(H)$ be positive. I know that if $\overline{A}B$ is normal, then $AB$ need not be normal. My question is: If $AB$ is...

30 January 2022 8,651 2 View

About the commutatvity of a bounded self-adjoint operator with an unbounded symmetric one?

Let $B\in B(H)$ be self-adjoint and let $A$ be a densely defined symmetric (and closed if needed) operator such that $A^2$ is densely defined. If $BA^2\subset A^2B$ say, is there a result which...

28 January 2022 9,354 8 View

About the closedness of a certain product of two closed operators?

Hi Let HH be a Hilbert space. Let S∈B(H) and let T be a densely defined closed operator such that TS⊂ST. Assume further that T is boundedly invertible and that both S and T are self-adjoint and...

14 January 2022 9,474 10 View

Anyone have clinical data to diagnose diseases ?

The data will be used to compose a dataset for training machine learning model to help in diseases diagnostics.

29 March 2021 469 7 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

How to scrape off the surface layer of compound sputtering targets as with multiple usage top layer's stoichiometry changes from the original target?

I am experiencing this for the Bi2Se3 sputtering target. Initially, even if the target was 2:3 in Bi : Se, with a few sputtering runs, due to the high escaping tendency of selenium, the top layer...

23 July 2024 1,649 1 View

Optimal condition for depositing FTO target 95:5% using sputter technique?

Hello I want to know about the sputtering condition of depositing FTO from target 95:5%. I tried with RF sputter in pressure 2.5Pa and 100 sccm Ar at room temperature but it showing no...

21 July 2024 1,680 2 View

How can we reduce the porosity of tungsten oxide (WO3) thin films during DC sputtering deposition (target: W, power: 100 W, 75 W, and 50 W)?

We are fabricating a tandem structure where a ~50 nm thick WO3 film is deposited between two metal films using DC sputtering. We use a mixture of Ar and O2 gases at different flow rates while...

01 July 2024 2,686 2 View

Why hall bar fabricated using photolithography and sputtering are not showing continuity with contact pads?

I am fabricating the Hall bar (5 micron width and 35 micron length) of Ta(3nm)Co(4nm)Pt(5nm) using photolithoghaphy and sputtering. This Hall bar is connected by contact pads of Ti(10nm)/Au(60nm)...

29 June 2024 2,079 3 View

How to solve the problem that the film obtained by magnetron sputtering on the ternary alloy target A2BC is ABC (not A2BC)?

Using magnetron sputtering with an alloy target composed of A:B:C in a 2:1:1 ratio, the resulting thin film composition is A:B:C=1:1:1. How can you achieve a A:B:C=2:1:1 composition? What are some...

24 June 2024 1,605 0 View

Why are there holes on the surface of TiO2 films deposited by ion beam sputtering?

We have observed many holes on the surface of TiO2. These holes have a diameter of approximately 1 µm and a depth of about 30 nm. The formation of these holes is mainly related to the...

20 June 2024 3,861 1 View

What could be the reason for the increase of baseline at low angles during GIXRD measurement?

I conducted GIXRD measurements after performing O2 plasma treatment on a Cu surface. It was observed that the baseline is significantly high at low angles (10-30 degrees). What could this...

18 June 2024 2,996 3 View

How to avoid SS contamination in RF magnetron sputtering?

Hello I am encountering Fe and other stainless steel (SS) element contamination in my LiCoO2 RF sputtering depositions. I suspect the source is the "etching" of the magnetron stainless steel frame...

11 June 2024 2,196 3 View

What is the reason for the non-monotonic variation of roughness for sputtered Cu films annealed at 100, 200 and 300 degree Celsius?

I have prepared Copper thin films by magnetron sputtering and the samples have been annealed at 100, 200 and 300 degree celsius. The variation of the rms roughness and all other AFM height related...

11 June 2024 9,774 1 View