07 September 2020 3 6K Report
  • BCS equation corresponding to electronic heat coefficient is given to the attachment.

  • Similar topics
  • Heat
More Subhadip Cdhakrabortty's questions See All
Is it possible to plot the Magnitude response of the filter having the following Difference equation, in MATLAB?

The given difference equation is Attached. I have to plot the Magnitude Response of the Filter. I have searched a lot about these types of Difference equations, and their Magnitude response in...

08 May 2020 4,110 1 View

How to plot the Magnitude response of a filter whose Difference equation is given as follows?

The given Difference Equation is : y(n)=0.33x(n +1)+0.33x(n) + 0.33x(n-1). Please help me how to plot the magnitude response of this filter. Any help will be greatly appreciated.

07 May 2020 8,451 15 View

Can anyone please help me to shade a particular region in MATLAB plot?

I have a 2D plot. I want to divide it into different parts. For Magnitude > 0.7, I want to shade it Red. For Magnitude 0.7 to 0.1 Blue. Please suggest me how to do it. Any help will be greatly...

06 May 2020 7,845 2 View

How to Highlight some particular Points in MATLAB?

I have plotted the response of a Filter using "freqs()". Now, I want to highlight the points on the plot corresponding to Y=0.1 and Y=0.1. Please suggest me how to do it. Any help will be greatly...

05 May 2020 9,504 8 View

I need some help with the Analysis of Signal in MATLAB having atleat 19056003 Data points. But in MATLAB its showing OUT OF Memory. Can anyone help?

For the study of discrete sequence in MATLAB, having about 19056003 points, MATLAB is showing OUT OF MEMORY. Is it possible to fulfill the task in MATLAB?

21 April 2020 1,767 10 View

Can I use gromacs order to compute tetrahedral order parameter of water?

I want to calculate Orientational tetrahedral order parameter of water. The output of gmx_hydorder is confusing. can I use gmx_order instead?

17 January 2020 6,623 4 View

What model should be used for exafs data fitting of hydroxyapatite?

I am trying to fit Sr K edge exafs data of Sr-substituted hydroxyapatite. I want to know about the choice of fitting parameters for the scattering paths. In particular, should I choose atom and...

11 February 2019 6,065 6 View

Is Lattice deformation zero in absence of electron-phonon interaction?

Lattice deformation is an important parameter for calculation in strongly correlated systems with electron-phonon interaction (EPI). In Hubbard holstein model used for studying strongly correlated...

07 October 2014 4,054 5 View

Can anyone offer advice regarding liver tissue lysate preparation for western blot analysis?

How to make tissue lysate samples?

08 November 2012 2,283 9 View

Any body help me regarding isolation of bronchiolar alveolar lavage from rat or mice?

I want to collect bronchiolar alveolar lavage from rat or mice...and see the cell count their

05 February 2012 1,323 2 View

Similar questions and discussions
What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

Mediation path analysis - Can I run two seperate models?

I am wanting to run a serial mediation model with 2 x IVs, 2 x MVs, and 3 DPs (all continuous). Is it problematic to run 2 different models for each IV, keeping the MVs and DPs the same in each...

27 February 2021 5,681 3 View

Exit velocity of natural gas from pressurized tank?

Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...

26 February 2021 6,253 3 View

Anyone that can help with Maxquant TMT16plex which is missing?

Hi I am very new to proteomics analysis. I have got raw files from core facility running thermofisher TMT 16plex 4 hours. I cannot find on maxquant the option TMT16Plex there is only up to 11...

25 February 2021 1,675 3 View

How to properly calculate the fluid solid heat transfer between polypropylene matrix and glass fiber in a porous medium?

I'm building a cfx model of thermoplastic pultrusion process on ansys and i have a doubt on how is the proper way to set this parameter in a porous medium

24 February 2021 1,915 1 View

How to properly calculate Interfacial area density in a porous domain?which are possible value for glass fiber?

I'm doing a cfx simulation of a multiphase flow in pultrusion and i set the Interfacial Area density in the heat exchange of a porous medium in this way IAD=Total fiber lateral surface of fiber...

23 February 2021 6,043 1 View

Physical-chemical formation of stalactites/stalagmites. what promotes the formation/growth of these structures?

I know, or think I do, the basic idea behind these natural structures, as from what I know they form due to water dripping from the top leaving a salt deposit behind. But started to wonder about...

22 February 2021 1,400 4 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close