How to perform biaxial tests to determine the yield loci of a VE using DAMASK?

04 February 2020 0 10K Report

Hello,

I am trying to use DAMASK (the Düsseldorf Advanced Material Simulation Kit) to find the yield loci for a VE of a sheet metal. I want to explore the s11-s22-s12 space along any desired path for a specific strain-rate value that does not change from one path to the other.

Is it possible to define the loading conditions as such to achieve this goal? I would greatly appreciate it if you can help.

Thanks, and regards, Soheil

Badges
Science topic

More Soheil Solhjoo's questions See All

Anybody can determine this micro-fossil?

Dear Researchers, I found it from Permian limestone strata in Julfa province (North-West of the Iran country). It should be mentioned, this microfossil extracted from samples collected of the...

29 March 2020 574 5 View

Can somebody help me and recommend publications for extracting Radiolarian microfossils from the Middle to Upper Permian strata?

Dear researchers, I'll be grateful if it is possible to recommend any method papers for extracting Radiolarian microfossils from the Middle to Upper Permian. Sincerely yours, Soheil.

22 March 2020 5,895 4 View

Can anyone suggest what is this microscopic fossil extracted from Middle to Upper Permian limestone strata?

Dear Researchers, I found it from Middle to Upper Permian limestone strata in Julfa NW Iran country. This microfossil extracted form sequences that belong to the Stratigraphy and bio-event...

16 February 2020 3,088 10 View

How can i control a DMD by FPGA?

I am trying to create some pattern with a DMD (digital micromirror device) and I want to configure a FPGA to drive the DMD but I'm running into some problems.

15 February 2020 9,508 3 View

Anybody knows what is this microscopic fossil from the Middle to Upper Permian limestone strata?

Dear Researchers, Anybody knows what is this microscopic fossil from the Middle to Upper Permian limestone strata? I found it from the Middle to Upper Permian limestone strata in Julfa NW Iran...

26 January 2020 3,108 4 View

The reason for increases and decreases of mainlobes and sidelobes in non-rectangular windowing?

I'm interested to find out the reason for increases of mainlobe's width and decreases of sidelobe's amplitude in windowing IIR filters with non-rectangular windows,like Bartlett,Hamming,... .

31 December 2018 5,615 8 View

Which Ductile material (preferably from polymer or glass ) we have with quick erosion rate on Abrasive Air Jet?

I'm Working on Reducing blast lag on the Abrasive air jet cross-sectional shaped material.

01 January 1970 6,905 19 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View