No title

02 March 2021 932 1 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Tooth extraction and subsequent dental implant placement in Sprague-Dawley rats induce differential changes in anterior digastric myofibre size and ?

01 March 2021 7,254 3 View

Is IMPACT FACTOR justified in case of Taxonomy?

There is huge pressure of getting good impact factor on scholars now a days. On the other hand Taxonomy is a very dry subject and the concerned papers can only get citation in same group of organism.

26 February 2021 5,851 1 View

Hi i want to ask that in order to find out LC 50 (96 hours) of particular toxin for fish. Should we keep the animals with food or without food?

if we expose the fish after acclimatization to particular toxin in order to find out LC 50 (96 hours).Should we keep the fish off feed or with feed for that duration. Some literature show that...

24 February 2021 357 2 View

How to simulate 5G Quality of Service characteristics?

For my research, I would like to simulate an end to end 5G network. My goal is to observe the behaviour of SDAP protocol, dynamic configuration of 5QI values etc. To summarize I would like to...

21 February 2021 7,624 3 View

How COVID-19 has affected mental health?

The pandemic has led to depression and anxiety and its negative effects shouldn't be ignored. However, it has also led some people to become more resilient! What do you think? Thank you.

21 February 2021 4,733 19 View

SSR primers are species specific or we can use it for any plant species ?

Hi, any one please guide me; SSR primers are species specific or trait specific. i have few primer which was reported in articles for wheat yield can i use these similar primer for lentil yield...

20 February 2021 315 4 View

Is There are any idea to achieve H NMR signals for swollen compound ??

the samples are not completely soluble - just swelled the solvents that's mean the sample may be partially soluble any suggestion, please

16 February 2021 8,801 3 View

Solution of 2D convection diffusion heat equation using MATLAB ?

This is a polymer heating problem. Polymer enters at around 180C (x=0) in the barrel. Also barrel initial temperature is 180 (t=0). Some heat Is added along whole length of barrel q. We have to...

15 February 2021 3,887 1 View

What element is driving the different slop in the low frequency tail?

My study consists simple corrosion inhibitors in salty brine. Right now I just fit my circuit with randles with CPE. Just wondering how the slop can given more info of the experiment. Or any...

01 March 2021 6,474 3 View

I need to accelerate corrosion in steel parts that are used in a salt-water environment. Is there a technique for doing so?

I have a structure that employs d-ring swiveling tie-downs that corrode during use and become "frozen". I have sample swivel assemblies that I wish to corrode to see if I can free them using one...

01 March 2021 3,739 3 View

What is the indication of the absence of peaks in Methanol electrooxidation CV curves ?

I have several question regarding the MOR; hope anyone help me better understand. 1- in CV using (KOH+MEOH) what is the indication of absence of the redox peaks? shouldn't they exist as a sign...

28 February 2021 4,851 8 View

Have anyone checked before Cyclic voltammograms of intial ITO substrate and E-teck?

As a beginner in electrochemistry, I tried to obtain cyclic voltamograms of commercial anatase powder deposited on an ITO substrate or on Eteck. After several attempts, I noticed that my cyclic...

23 February 2021 3,175 3 View

How can I measure the thickness of thin layers deposited on textured glass susbtrates?

I want to measure the thickness of aluminum oxide and titanium oxide layers deposited on textured glass substates. The layer thicknesses are typically below 100nm.

21 February 2021 5,465 4 View

How to do a surface treatment of uncoated TiO2 with polymer?

Basically, I would like to know how to treat or coat on the uncoated bare TiO2 (Ti-OH rich) surface with polymer which has anchoring groups in the polymer structure like trimethoxygroups. What is...

21 February 2021 4,657 6 View

How to Study a proton NMR of Graphene prepared by Electrochemical Exfoliation technique?

I performed a Proton NMR of graphene powder prepared by electrochemical exfoliation technique. It shows some peaks. But I can't understand it.

21 February 2021 8,947 3 View

How to predict the reaction pathway for electro organic synthesis?

Can anyone recommend some any software/models available that can predict substance reactivities and the reaction yield under a specific set of reaction conditions process and proposing pathways to...

17 February 2021 2,383 3 View

I want to remove TiO2 and SiO2 coating from surface. any one can help me?

I want to remove TiO2 and SiO2 coating from surface. I think that i should use HCl and MgCl2 and an oxidation agent such as potassium nitrate, but i dont know in which propertion should these...

14 February 2021 300 3 View

How to improve the adhesion of epoxy coating on steel substrate? Which factor affects?

I am facing a problem regarding a de-adhesion problem with the coating. A brief description of my methodology is given below. I am using mild or Low Carbon steel as a substrate and I polish the...

14 February 2021 2,167 4 View