Why do the air flow results vary totally when adding scalar in CFD ?

Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...

25 February 2021 9,602 4 View

What are effects of steel jacketing on flexural strength?

Dear all, If steel jacketing is used to retrofit a reinforced-concrete (RC) column, can we use it to improve flexural strength? I understand that we leave gaps between the ends of the jacket and...

22 February 2021 1,906 5 View

Room Occupancy Calculation ?

15 February 2021 1,997 6 View

What Buffer should i use for T4 virus for electron microscopy ?

Hello, I currently have my T4 virus in HEPES buffer. Unfortunately, there are always crystals that are contaminating my solution (due to the buffer in which the Viruses are) when I observe them...

01 February 2021 400 3 View

Can we use control variables during Structural Equation Modeling with Amos?

We want to explore a mediating relationship employing SEM with Amos SPSS. Our independent variable is attitude toward wife abuse. mediator is exposure to male marital violence, and outcome...

07 January 2021 4,481 3 View

Response Surface Methodology?

I'm using 3 different light intensities (constant values 15,30,45 W) for the wastewater treatment of an organic compound and optimizing the parameters (pH, catalyst dose and light intensity)...

31 December 2020 2,377 4 View

How to simulate a varying load /load profile in Simulink/MATLAB?

I am looking for a block in MATLAB that can simulate a varying load such as a load of a house given below. this block will be connected to a power system

27 December 2020 5,835 5 View

Is Psychotherapy effective for children than adult? Why? Is there any good article to respond that?

I study and research about anxiety disorders in children in Iran and I sometimes face questions like this and unfortunately I could not find article or book to answer that.

30 October 2020 6,822 7 View

No title

30 October 2020 961 3 View

Is there any possibility to precipitating of sugars and proteins along with kefiran precipitation from fermented whey by cold absolute ethanol?

Fermentation was performed by inoculating Lactobacillus kefiranofaciens in cheese whey. I have separated the biomass after 72 h of fermentation and I want to measure exopolysaccharide i. e....

20 October 2020 7,976 2 View

Buffer Exchange using column packed with sephadex G-25 effect on protein concentration?

Hello, If i am doing a buffer exchange for an antibody of 1mg/mL, does the elution lose protein in the process of buffer exchange? For example, if i flow through 500 uL of 1mg/mL sample, and...

03 March 2021 6,299 3 View

No title

03 March 2021 5,360 2 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

12% ledeburitic cold work tool steel, etched for revealing retained austenite, any help for clarifying?

Hello everyone. Given microstructure image belongs to a 12% ledeburitic cold work tool steel (annealed and tempered). The sample was etched with picral (100 mL ethanol and 4 g picric acid). I...

02 March 2021 4,119 3 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View

How Can I bring as much common elements in steel as possible to calculate stable phase(s) in OpenCalphad?

As I was tweaking step-by-step OpenCalphad6 Macros step1.ocm involving phase and thermal property calculation of a High-speed steel, I could not incorporate more than 6 elements in the steel...

01 March 2021 8,840 1 View

I need to accelerate corrosion in steel parts that are used in a salt-water environment. Is there a technique for doing so?

I have a structure that employs d-ring swiveling tie-downs that corrode during use and become "frozen". I have sample swivel assemblies that I wish to corrode to see if I can free them using one...

01 March 2021 3,739 3 View

Why is my platinum counter electrode getting dirty during electrodeposition?

I am conducting anodic electrodeposition of MnO2 onto a stainless steel substrate, using a platinum strip as a counter electrode. This is done galvanostatically, with the current held between 5...

27 February 2021 1,829 3 View

How can we raise the figure when we writing a paper with Latex ?

Hi, everyone. I'm a starter to write a paper by Latex. But I have some difficulty using it. I'm writing the paper with 2 columns. And, there is one figure that occupies the 2 both-sides. I want to...

26 February 2021 3,738 3 View

What is the best way to calculate the angles of twist for concrete columns subjected to torsional moment using finite element software?

In Finite element software like ANSYS , there is difficulty in obtaining direct results of twisting of concrete members because SOLID65 which is the unique element designed to represent concrete...

26 February 2021 3,806 2 View