What is the detection limit of ED-XRF technique for transition metals in silicon ?

Hi everybody, please, can someone tell us if the transition metals (W, Fe, Ni, etc ...) in silicon destined for solar cell manufacturing can be detected by ED-XRF technique. Note that the...

18 February 2021 6,231 4 View

How can I obtain a thin film of PDMS liquid?

I would like to prepare a thin film from of PDMS liquid. My current attempts with solvent casting, then let it dry for 24 hr at room temp. after I tried to recuperate and it doesn't work. Any...

08 October 2020 8,745 4 View

Can I use figures from my published paper without reference to the source ?

Dear researchers, Recently, my paper got published in a journal. however, i have used two figures from this published paper without reference to the source, in other paper (current statut:...

02 October 2020 2,708 5 View

Should unlimited vacations be generalized?

A few days before the start of the new school year, would you like to take a few more weeks of vacation? In some companies, this is possible thanks to unlimited vacations. Based on individual...

25 August 2020 7,621 12 View

Should the Russian Vaccin against COVID-19 be approved and produced in Octobre Or it must be backed up with more studies?

09 August 2020 2,291 7 View

How much accurate is the cropland area sourced from FAOSTAT?

Along with other statistics, FAOSTAT provides the cropland area for all countries (in 1000 ha). These estimates were used by many scholars to assess their cropland maps' quality (the closer of the...

06 July 2020 7,965 2 View

Where to find UHF RFID tag development Kits?

Hello, I am looking for an RFID tag development kit. I can see development kits for the reader but there are no kits for the tag. I need a kit that has a separate modulator, charging circuitry,...

17 May 2020 9,221 7 View

Is there a need of SeqScape soft ware and Variant reporter soft ware in MLPA data analysis process ?? Or it is only the coffalyser which is needed ?

Is there a need of SeqScape soft ware and Variant reporter soft ware in MLPA data analysis process ?? Or it is only the coffalyser which is needed ?

16 March 2020 9,640 1 View

Can freemeteo.com website be used as a valuable source for Meteorological data extraction?

I have found different historical climate data from freemeteo.com website so I would like to inquire if I can use it as a source to extract the data I need and make it as a reference within my...

03 March 2020 1,539 3 View

How to compute the probability for a firm to move from on group to another in a panel database?

Hello, I have a panel database for firms i (90 firms) across year t (from 2013 to 2019). Some firms witnessed a cross border investment in a year that is between 2013 and 2019. I created a...

06 December 2019 5,778 3 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Why does blocking with my immunogenic peptide cause nuclear fluorescence in ICC?

Hi all, I am validating a polyclonal antibody raised against human ANT4, through WB and ICC. In most of my controls, the antibody shows very little off-target binding, but when I pre-incubate the...

03 March 2021 5,999 3 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View