How to model infiltration in RS3?

More Tharshikka Vickneswaran's questions See All

Extracting fluroxypyr and prothioconazole from soil?

Hi, I am currently trying to extract the pesticides fluroxypyr and prothioconazole from the soil by spiking using Dutch Mini Luke extraction method; however, I am failing. The instrument used for...

18 November 2020 4,006 9 View

Separation of solvents in Dutch Mini Luke pesticide extraction method?

Hi, I am looking to test the effectiveness of pesticide residues extraction from the soil sample using the Dutch mini luke extraction method. The extraction method would involve the mixing of...

19 October 2020 1,318 4 View

How significant will be difference of soil phenolic content between primary forest and oil palm plantation ?

I would like to develop a hypothesis for my project where i study the difference of soil phenolic content between two different land use types (Primary forest and Oil palm plantation). I want to...

18 May 2016 6,666 2 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

After a reference from Int J Body Compos Res, can any body help?

Hi, I am after the reference below, my library says it cannot obtain a copy either locally or internationally, any help appreciated! Chris Wang ZM, Heshka S, Wielopolski L, Pi-Sunyer FX, Pierson...

03 March 2021 6,193 1 View

What techniques can I use to determine the miscibility of polymer blends?

The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...

03 March 2021 4,107 4 View

Gel electrophoresis result for total RNA samples, 1.5 Agarose gel was used, How to improve the integrity of RNA?

Gel electrophoresis, RNA degradation, RNA extraction from fresh tissue

02 March 2021 5,433 5 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

Shall I skip the measurement model in SmartPLS?

Hello everyone, I had run a mediation model in SmartPLS using questionnaires that were already validated among my statistical population. A professor who edited my paper -though she is not...

01 March 2021 3,052 3 View

What is involved in morphological changes of SEM images of a substance?

In the sem analysis of CaCO3 nanaoparticles, the morphology images showed spherical shaped particles but the proposed morphology for these type of nanoparticles is trigonal. I prepared the...

01 March 2021 1,960 4 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View

Does the circuit modeling for planar monopole antennas using Foster canonical forms give good approximation?

Hi researchers, I am searching for some accurate way to do the circuit modeling of planar CPW-fed monopole antennas. I have gone through the literature where mostly circuit modeling is done using...

28 February 2021 7,016 1 View

Eugie Kabwe

It seems you want to model particle flow by employing...RS3 numerical code, do you have access to any other numerical code options..i.e PFC3D...?..

Sina Javankhoshdel

Hi Tharshikka,

You just need to select a surface and apply the infiltration boundary condition to it. About the suction, you can select an option in the Project setting to put a cut off for the suction. Please email me if you have further questions: [email protected], I will be happy to help.

Cheers,