How to model a transistor in SIMULINK using its datasheet?

Erfan Hamsayeh Abbasi Niasar @Erfan_Hamsayeh_Abbasi_Niasar2

05 May 2019 0 610 Report

Hello everyone,

I'm having difficulty in modeling a transistor using its datasheet in SIMULINK, because the parameters in the datasheets are different from the ones in SIMULINK. I was wondering if somebody can help me with this.

Thanks

Badges
Science topic

Similar topics
Engineering
Modeling

More Erfan Hamsayeh Abbasi Niasar's questions See All

How to link a neural network generated in MATLAB with an optimization algorithm?

Hello everyone, I was wondering if anyone can help me on this. I generated an MLP neural network in MATLAB, and the output is a blackbox named net(x). I want to use this function as an objective...

02 March 2019 5,447 3 View

How to have a plot against two variables in Matlab?

Hello everyone, I'm trying two plot a curve against two variables in Matlab but I'm having problems. Here's the thing. I need to plot Stress vs Power and h/d simultaneously but Matlab gives me...

06 July 2018 9,872 1 View

How to define APC-840 material in COMSOL Multiphysics?

Hey guys. Does anyone here know how to define APC-840 piezoelectric material in COMSOL? If anyone has already worked on it, please let me know. thanks

09 October 2017 9,010 5 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

After a reference from Int J Body Compos Res, can any body help?

Hi, I am after the reference below, my library says it cannot obtain a copy either locally or internationally, any help appreciated! Chris Wang ZM, Heshka S, Wielopolski L, Pi-Sunyer FX, Pierson...

03 March 2021 6,193 1 View

What techniques can I use to determine the miscibility of polymer blends?

The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...

03 March 2021 4,107 4 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

Shall I skip the measurement model in SmartPLS?

Hello everyone, I had run a mediation model in SmartPLS using questionnaires that were already validated among my statistical population. A professor who edited my paper -though she is not...

01 March 2021 3,052 3 View

What is involved in morphological changes of SEM images of a substance?

In the sem analysis of CaCO3 nanaoparticles, the morphology images showed spherical shaped particles but the proposed morphology for these type of nanoparticles is trigonal. I prepared the...

01 March 2021 1,960 4 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View

Does the circuit modeling for planar monopole antennas using Foster canonical forms give good approximation?

Hi researchers, I am searching for some accurate way to do the circuit modeling of planar CPW-fed monopole antennas. I have gone through the literature where mostly circuit modeling is done using...

28 February 2021 7,016 1 View

How to modify Johnson cook equation in ABAQUS?

I wanted to add an extra parameter to the existing Johnson cook equation in the ABAQUS simulation. How to add those extra parameters. Ref: A modified Johnson-Cook material model with strain...

28 February 2021 4,841 3 View