How to make a thick and flat chrome metal strip?

Yasaman Hosseinpour @Yasaman-Hosseinpour

29 May 2020 1 4K Report

What is the method for making a thick flat chromium strip by powder metallurgical method in a container? Is it possible to use a hydraulic press in the environment to compress it?

Muhammad Hamzah Saleem

Following

Badges
Science topic

More Yasaman Hosseinpour's questions See All

Choosing an appropriate TLD for mixed radiation?

Could you please recommend the appropriate TLD card model for both personal and environmental dosimetry in a high-energy proton accelerator center, specifically for dosimetry of beta, gamma, and...

17 June 2024 1,958 0 View

Evaluation of seismic resilience of steel structures?

Question about how and types of methods to optimize steel structures for seismic resistance

29 February 2024 7,569 4 View

Which technique is more cost-effective and approved to evaluate the functionality of neurites? patch clamp or multi-electrode arrays (MEAs)?

I want to functionally evaluate scaffold-grown neurites in vitro and need a validated technique that provides results at a low cost and in a short time.

25 November 2023 4,387 1 View

I'm fabricating a thermosensitive hydrogel made of chitosan and beta glycerophosphate. It doesn't gelate. Do you have any idea?

It's fluid in 4 centigrade degrees but when I put it in 37 centigrade it doesn't gelate after even 1 hour. I checked the pH before putting the solution in the 37 centigrade. It was 6.3. I add up...

01 October 2023 5,139 0 View

Coding in MATLAB software and calibration film, I have the image of the Gaff Chromic scanned film and I want to convert it to dose in MATLAB software?

I have exposed the Gaff Chromic film and then scanned it, now in MATLAB, I have to write a code to convert it to dose and then obtain the calibration curve of the film.

16 September 2023 7,428 4 View

I was wondering if anyone here has published their research in Arxiv category eess.AS (Audio and Speech Processing)?

I want to upload my research paper on Arxiv eess.AS (Audio and Speech Processing), however I need endorsement for this category even with my university email. I would appreciate it if someone can...

20 July 2023 3,471 0 View

In order to evaluate the function of neurons and neurites in vitro, what techniques can be used ?

In addition to the patch clamp technique, what other techniques can be used to evaluate the function of neurons and neurites in a laboratory environment? we don't want to implant our scaffold...

06 June 2023 2,615 0 View

To evaluate axon and neurite growth, which cells can be co-culture with Schwann cells in vitro?

To evaluate neurite growth in vitro on neural scaffolds with Schwann cells, what cells can be used besides PC12?

21 May 2023 7,417 2 View

I have a question about the Foresight (or Futurology) in AI?

How can I find general scenarios (drivers with uncertainty) of artificial intelligence in the world, as well as scenarios of artificial intelligence in America, China and Russia?

20 October 2022 574 6 View

Why do not we have efficient attachment of Aptamer to AuNp by protocol of related articles??

My project is about electrochemical biosensor for a breast cancer … I have a problem… In my project a glassy carbon electrode (GCE) modified with electrodeposited Au nanoparticles (AuNps), an...

23 August 2022 3,799 0 View

Why doesn't chromium 2+ ion use all its d-orbitals to receive lone pairs from six waters in [Cr(H20)6)]3+?

I'm guessing it's because the ligand experiences too much electron repulsion or proton repulsion from the chromium to insert them close to the 3d-orbitals which are close to the metal nucleus. Is...

03 August 2024 1,370 1 View

How does the Retention time effect the Biogas Production?

List down the various factors responsible and how does this effect the overall biogas production when it is related to Hydraulic retention time of the digester based on the feedstock?

27 July 2024 4,800 4 View

Mechanochemistry: ball to powder mass or ball to powder volume?

I run mechanochemical reactions that involves the use of a large amount of catalyst (1:1 molar ratio to the reactant). When I try to understand the effect of amount of catalyst on the reaction, I...

23 July 2024 9,938 1 View

I want to plot calibration curve of pure mirtazapine powder using HPLC. Can someone please suggest a method without HPLC buffer as a mobile phase?

I am searching for HPLC method to estimate Mirtazapine but i want to avoid HPLC-buffers as a mobile phase component. So, I am looking for alternative HPLC-solvent (acetonitrile, methanol etc.)...

14 July 2024 1,493 3 View

Does anyone know, any conference related to "mathematical data compression" topic?

Please suggest me, I want to present my research work.

13 July 2024 1,461 1 View

What binders suggestion that I can use for zinc alloy?

I am working on powder metallurgy, and during the compaction process, the powder does not pelletize and remains in its powder form. To address this issue, I am considering using binders to improve...

13 July 2024 9,003 2 View

How i figuer out the weight of curcumin powder?

I am trying to load curcumin emulsion in 4% chitosan gel but i don not know how many mg powder is needed ?

10 July 2024 2,462 1 View

Can anyone suggest what amount of powder I have to disperse in the solvent for taking the FTIR spectra?

I have to compare the FTIR of the two samples, one is in powder form and other one is the powder dispersed in IPA or water. Both are same material, so how the bond will change

09 July 2024 8,011 2 View

Is VSM measurment of NdFeB alloy powder sample require any spesific sample preparation ?

Is any specific sample preparation required to perform VSM measurement of NdFeB alloy powder to get a square-shaped M-H loop? Or is it mandatory to make magnetically aligned and sintered pellets...

09 July 2024 1,969 0 View

I have need a LPBF/SLM model on comsol multiphysics ?

In this model clearly understanding how to active one layer to another layer and how to add powder material properties step by step.

08 July 2024 6,147 0 View