How to interpret spread-ability and extrudability data obtained by stable micro system?

More Sunita Patil's questions See All

How to analyze a particular region of my simulation box in GROMACS?

Hi, I am using GROMACS 5.1.4 to simulate water in contact with a surface. I am only interested to calculate some properties of water near the surface. Let's say at a distance of x nm from the...

03 March 2021 9,989 2 View

What are the important tips for writing review articles?

Important tips for writing a good review articles

24 February 2021 8,544 6 View

Can the Dunn's test be used as an appropriate post-hoc for the G-test?

Research Question: Are red grouse (Lagopus lagopus scotica) a statistically significant proportion of raptor (bird of prey) diets? I am planning on using a series of G-tests (determining whether...

23 February 2021 5,827 3 View

What low-cut filter (high Pass frequency) to be used for response spectrum (Tripartite plots) ?

What low-cut filter (high Pass frequency) to be used for the response spectrum (Tripartite plots)? I am currently working on differentiating between hard/soft site responses in Indo-Gangetic...

21 February 2021 9,273 2 View

Where can the fault diagnosis data set of lithium battery be found?

Most of the data sets on the network only contain good information about the voltage and internal resistance of lithium batteries. The data of faulty battery is missing. Who can help me, I will be...

21 February 2021 8,659 1 View

How to define the sink temperature and film coefficient?

Hi, everyone. I am considering the heat conviction during compacting simulation by Abaqus. I was wondering that how to define the sink temperature and film coefficient? Is there any references...

21 February 2021 6,197 1 View

How to discriminate between Sentinel-2 Level-2A Product Discriminators?

According to the Sentinel-2 user guide here (https://sentinel.esa.int/web/sentinel/user-guides/sentinel-2-msi/naming-convention), the compact naming convention is arranged as...

21 February 2021 5,919 9 View

Are ZnS nanoparticles moisture sensitive?

Hello Everyone, I tried to form ZnS nanoparticles using the hot injection method and was able to form the same (confirmed by XRD). When I centrifuged, after the reaction I got a kind of white...

17 February 2021 1,709 3 View

Can anyone suggest a software for running a plant tissue culture lab?

A software which can help to design the experiment, store data, update new data, set subculture reminders, barcoding etc. Like Invitrosoft.

17 February 2021 3,015 5 View

Is an encrypted dataset with Microsoft SEAL compatible with Cloudsim simulator??

Hello, I would like to do homomorphic encryption using Microsoft SEAL on my dataset and then use it as an input to the Cloudsim simulator to do clustering on. Is it possible and compatible with...

16 February 2021 3,915 1 View

What degree of missing data in a particular case/participant results in Expectation-Maximisation no longer working?

I'm dealing with a mediation model and am using the PROCESS module in SPSS. Due to SPSS and PROCESS being limited in the imputation methods - being unable to handle multiple imputation - the other...

02 March 2021 4,362 1 View

Is There Any Feasible Method To Test Fluorescent Compounds Other Than Fluorescence Spectrometers ??

Is There Any Feasible Method To Test The Efficiency Of Fluorescent Compounds Other Than UV Spectrometers ? Suggestions Would Be Appreciated !

02 March 2021 5,785 3 View

How can I represent SDS-PAGE results for machine learning analysis?

I am trying to classify and analyze the results of an SDS-PAGE based array for bacterial detection using machine learning, but I have trouble finding the best way to represent the results with...

27 February 2021 9,176 3 View

Mixed ANOVA - help?

I'm currently working on a piece which asks to conduct an ANOVA - looking at the effect of sporting group (2 levels), and exercise trials (two trials with six levels). I've computed this all...

27 February 2021 9,626 4 View

Why my agarose gel staining sometimes looks not homogenic but like gradient (see the figure)?

I am worried about this overexposure of the upper part of the gel in the picture. Is it possible that this is the result of too much concentration of ethidium bromide? Why is there such a big...

25 February 2021 8,140 3 View

How to Interpret Partial Eta Squared Numbers For a Repeated Measures Anova?

I have obtained Partial Eta Squared Numbers through Two-Way Mixed Anova Analysis. My results for different constructs are: .105, .135, .038, .068, .061 respectively. I wanted to know, whether...

24 February 2021 7,122 1 View

EMSA troubleshooting. Protein-DNA complex not migrating, cold probe lane with multiple bands. Can anyone help?

I'm running an EMSA to show the DNA binding activity of recombinant proteins versus the Wild type. Previous assays run by my research group using a different test system show the protein-DNA...

24 February 2021 8,325 1 View

Problem with ligating 2.8 kb insert into 8.5 kb plasmid?

I am trying to clone 2 copies of the same mammalian gene into the pSF-CMV-Ub-Puro Ascl (contains HindIII, KpnI and NheI cut sites) plasmid. This is what the final product is supposed to look like...

24 February 2021 6,310 3 View

How to manage western blot for proteomics data validation?

Hi Everyone, I am a bigginer in western blotting and I am trying to use it for validation of my proteomics data. I have: two regulated proteins with molecular mass of 40 and 73 kDa one control...

23 February 2021 6,671 4 View

Alginate and silk fibroin hydrogels toxic to cells?

Hello, I asm currently working with alginate and silk fibroin hydrogels. I prepared a blend of alginate and aqueous silk fibroin (straight from dialysis) and resorted to ionic crosslinking to...

23 February 2021 8,249 2 View

Jan Engmann

Can you describe a little more precisely (a) your formultion, (b) what you and measured (c) what you would like to compare/predict/design for?

Sunita Patil

Thank you Sir for your interest.

I have evaluated carbomer gel using stable microsystem for spreadability and extrudability the graph obtained are attached here with from which I want to see its ease of spreading, consistency and ease extrusion from its firmness and work of shear.