Pulse Detonation Engine is high performance system, but it is known to be prone to high heat flux generation, when run for longer duration
Please refer to the file attached. All the best
I got a good idea of heat flux management of PDE. I will implement it.
Thank you sir
good idea
A crude extract of fungal culture using EtOH was subjected to column and TLC and partially purified compound was obtained. UV vis spectrum of the compound/s has max absorbance at 218nm. The...
11 August 2024 9,801 2 View
I am attempting to conjugate PEG to an amino acid at the C-terminus, for the purposes of producing nanoparticles. I have been told that PEG modified with amine groups can be used for this purpose,...
31 July 2024 2,033 1 View
Am trying to develop a lesson/lab to determine and compare antioxidant properties of soybeans of various colors. Preference would be low tech and low cost. Any assistance is greatly appreciated.
25 July 2024 7,498 2 View
In running two-dimensional gel electrophoresis on bacterial protein, some spots that appear to match a protein sequence have a significantly more acidic isoelectric point than the calculated pI....
24 July 2024 8,076 3 View
Their is new research published in the biological control journal, and I am one of the authors. I want to add it to my account at researchgare. How can I do this?
21 July 2024 7,545 0 View
I have read that it is better to use other research methods alongside document analysis for triangulation, although it can also be used as a stand-alone method.
18 July 2024 4,218 0 View
I am conducting a study on Effectiveness of e-content on academic achievement of secondary school science student.
17 July 2024 5,633 4 View
I am simulating interlocking / dry stacked masonry in Abaqus. I am using a friction coefficient of 0.6 for my model as it is stated in the previous research as well as in the base paper. The...
16 July 2024 5,047 0 View
im studing gaussian 16 with reading paper about I-131 Metaiodobenzylguanidine in the paper "In a similar vein, nuclear magnetic resonance shielding values were investigated using the widely...
16 July 2024 6,040 4 View
I am doing a systematic review, and I am measuring risk of bias with RoB2 for RCT, and ROBINS-I for non RCT. My questions is, for single arm studies, can I use ROBINS-I? I am not sure how to...
14 July 2024 3,570 5 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
Dear QE-users, In the method where full MS positive mode and PRM mode are used, we always get an incorrect auxiliary gas reading (41 instead of 25). This only happens in this method; other...
06 August 2024 4,953 0 View
Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...
06 August 2024 1,989 3 View
is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it
06 August 2024 947 1 View
Hello guys! Do you have experience running a Oaxaca-Blinder decomposition on R applying person weights. How do you suggest doing it? I have a variable PERWT which gives more information on how...
04 August 2024 6,033 0 View
I want to Estimate surface heat fluxes using MyLake, but I don't have all the initial values in model parameters section and other sections,is there a way?
04 August 2024 1,537 1 View
I am using a Bruker 600M solid-state NMR spectrometer with a Micro 2.5 microimaging system. The test sample is a tube of 1M LiCl aqueous solution, and the nucleus detected is 1H. I am trying to...
01 August 2024 9,227 1 View
Hello Everyone I have a question about structure for connectivity analysis on sources. My goal: preprocess and cut data into trials create headmodels, using template MRI file perform source...
30 July 2024 2,744 1 View
When I run autogrid4 it says: autogrid4: ERROR: Unknown receptor type: "Cr" -- Add parameters for it to the parameter library first! Look forward to your reply.Thank you so much!
29 July 2024 488 0 View
I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...
29 July 2024 9,572 3 View