How to identify Zeta phase in Cu-Sn alloy?

07 July 2015 1 3K Report

How to identify Zeta phase and distinguish between Zeta and Alfa+Delta phase in Cu-35%Sn alloy with some Lead inclusions.

Gert Nolze

You can use also EBSD if the phase has a remarkably different structure.

Badges
Science topic

More Siddharth Shankar Rai's questions See All

How to de-normalize quantitative data obtained by EDS?

I have EDS data (wt% normalized) of metal samples having composition of Fe 79.69, Sn 5.93, C 11.69 and O 2.75 %wt. I want to remove C and O from my data and calculate exact ratio of Fe and Sn. How...

09 October 2015 7,578 5 View

How to convert an XRD JADE (.pid or .raw) file into a file supported by X'Pert HighScore Plus?

I have data obtained by rigaku rint XRD through JADE software. My data is in *.pid and *.raw format but unfortunately X'Pert HighScore Plus is not supporting both file format, so i I want to...

02 March 2014 3,789 38 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

Best mask design for metal deposition aiming build a Perovskite solar cell device?

What types of mask designs for metal deposition, to be used in a PVD system, are best suited for perovskite-based solar cells?

31 July 2024 4,835 3 View

How select composition for ods-high entropy alloys?

31 July 2024 2,795 1 View

I am trying to obtain microstructure for Mg-Zn-Sn alloy?

Any suggestions with respect to etchant composition and holding time?

27 July 2024 6,925 2 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

Is there a good macro photography kit for on-site metallurgical investigation?

I am looking to purchase a photography kit for onsite metallurgical investigations, such as capturing photos of worn areas, hot tears, cold tears etc. Could anyone suggest me a good...

22 July 2024 3,490 2 View

What could be the possible reason that sintering of polycrystalline diamond fabricated with tape casting has suddenly started failing?

I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...

16 July 2024 3,212 5 View

What binders suggestion that I can use for zinc alloy?

I am working on powder metallurgy, and during the compaction process, the powder does not pelletize and remains in its powder form. To address this issue, I am considering using binders to improve...

13 July 2024 9,003 2 View

How to select temperatures for two-step aging treatment in high entropy superalloys?

Waspaloy is considered the benchmark alloy. Due to the different gamma prime solvus temperatures, we couldn't adopt the same double aging treatment. Can anyone suggest how to select temperatures...

13 July 2024 2,417 1 View

What is the mathematical expressionof theoretical yield strength calculated considering solution strengthening in stainless steel 316L?

In the expression for solid solution strengthening model that has been widely used in the literature use a linear form consisting of strength coefficient, and concentration of elements in wt.%....

11 July 2024 4,476 3 View