What are state-of-the-art methods/techniques/algorithms for the root-cause analysis of the anomalies?

I have been looking for research articles that target the question "why did an anomaly occur?", however, most of the papers that I found are related to "if an anomaly occurred?". I searched Google...

12 January 2021 7,951 3 View

How to amplify lignin degrading gene?

Hello colleagues, I would like to amply the lignin-degrading gene (i.e., LigX, LigY, LigZ, and LigW) from different types of soil. I have tried to find literature, but unfortunately, there are...

20 October 2020 9,654 3 View

How to remove abnormal behavior at support of FE model of RCC Beam?

Hi, I am modelling a half model of RCC beam in ANSYS Mechanical APDL. The model I have created is exhibiting abnormal behavior at the support with abnormal cracks. I would be grateful if you...

12 October 2020 8,596 3 View

How to calibrate the parameters of coupled damage-plasticity microplane model of concrete for FE modelling of RCC beam in ANSYS Mechanical APDL?

Hi, I am trying to model an RCC beam in ANSYS Mechanical APDL. I have the value of Compressive strength, and modulus of elasticity of the concrete of the experiment I am trying to validate ? Can...

28 August 2020 4,623 2 View

Values for Fouling rate in superheaters and economizers in biomass boilers?

I currently work on analyzing fouling rate in BFB biomass boiler, based on available measurements. Looking through literature, the only reported values I found were from certain TEMA Tables, from...

19 April 2020 1,973 5 View

What is the best methodology to use for development of Mobile Applications?

In Software Engineering the UML is considered a standard way in design of the system. What will be the best in designing the mobile applications?

24 January 2020 5,777 3 View

What are the effects of using powerful magnets around AC current?

I am trying to connect two sockets( sockets being flat surfaces on both sides) using powerful (small sized ~8mm diameter) neodymium magnets with 3 or 4 on each side of the socket so that the pull...

03 January 2020 8,835 3 View

How to determine molecular weight of disordered peptides from diffusion NMR data?

From diffusion NMR (DOSY) experiments, diffusion coefficients are available for ~40 AA disordered peptides. Is there a method to calculate the molecular weights using these data, that is suitable...

08 July 2019 703 3 View

Is there a way to blast a protein against all known proteins to find common epitopes? (Even if they are a couple of amino acids long)?

I read somewhere that some vaccinations result in the onset of a different disease that is due to the fact that the vaccine and another protein inside the body have a shared epitope and are both...

22 October 2018 7,832 3 View

What is the best way to differentiate between efferent and afferent sympathetic nerve fibres immunohistologically?

Efferent as afferent renal sympathetic nerve fibers have a important relevance in the development of cardiovascular disease. Thyrosine hydroxylase is a marker for sympathetic fibers. Is there a...

04 June 2018 4,657 2 View

How can we limit artifacts caused by rotation in fiber photometry?

We are trying to run fiber photometry experiments for long time scales, but we get these sinusoidal artifacts that come up. We think they may be caused by twisting of the fiber optic subject...

25 February 2021 568 1 View

How do you integrate the 'friction' variable Xi in the Nose - Hoover Thermostat in order to apply it to a molecular dynamics simulation?

Everything tells you the derivative of Xi, but not how integrate the value to implement it into a simulation. How do you do this?

21 February 2021 6,481 1 View

How to implement boundary conditions in Abaqus contact problems?

Hello I am trying to simulate crawling motion of a bilayer beam using Abaqus. Kind of similar to this: https://youtu.be/os-Z3ucoFpA I am using multiphysics enabled (diffusion, deformation,...

20 February 2021 2,916 1 View

Buckling analysis of a cylindrical shell in Ansys APDL?

In Ansys APDL, We are trying to validate our shell model for nonlinear buckling analysis considering the initial imperfection (as given by Ahmed et. al.) We have attached our results as attached....

13 February 2021 9,200 5 View

How to deal with cross loadings in EFA?

There is an issue of cross-loadings in my output results after running an EFA with varimax rotation. Should I ignore these cross-loadings since these differ by more than .20?

12 February 2021 802 4 View

When to use Darcy or Fanning friction factor in frictional pressure drop measurement?

04 February 2021 6,174 3 View

Is it necessary to include orbital dynamics (translational) in attitude dynamics (rotational) problem?

I want to simulate satellite attitude control with a quaternion attitude representation. thrusters and reaction wheels are the main AOCS controllers. is it Ok to omit orbit dynamics (orbit...

31 January 2021 5,094 2 View

how to add blood and plasma in comsol?

I am trying to model separation of the plasma from the blood on a rotating microfluidic platform. I am not able to add blood and plasma in Comsol. someone please provide me your valuable...

27 January 2021 8,263 1 View

How to rotate an anisotropic stiffness matrix to an orthotropic matrix of cancellous bone?

Hi everyone, recently i have a question about how to calculate the orthotropic elastic matrix of cancellous bone cube. I really need the help!!!! I applied six stress states to the cancellous...

21 January 2021 9,143 2 View

Anybody to help me with Code source for DOUBLE CONCAVE FRICTION PENDULUM BEARINGS Please?

Hello, would you please share the codes for Base Isolation of structures using Double Concave Friction Pendulum Bearings? I am doing a related research but as I am just a beginner in MATLAB, I...

18 January 2021 6,683 1 View