Transformation matrix between Canonical Form I and II?

How to calculate transformation matrix of order nxn between two canonical forms of order nxn ?

31 December 2016 5,805 2 View

How should we choose the values of grid LC filter in grid connected PV Systems?

There is large variety for choosing the values of L and C for filter design. Kindly suggest the standard way for calculating L and C values for the grid connected PV System.

04 May 2016 2,142 0 View

How do we use inductor as a transformer in load flow simulation??

Actually I want to know how inductor or LC filters are used in place of transformer (Step up or step down) in MATLAB/Simulation with proper calculation? Kindly give answer with your respective...

01 February 2016 6,739 0 View

Grid connected PV system parameters details?

Kindly provide grid connected PV system parameter details and how to calculate and decide the parameters for these kind of systems?

01 February 2016 9,643 1 View

What are the necessary conditions to connect photovoltaic systems to grid?

In terms of parameters what are the conditions that must be satisfied by photovoltaic systems while integrating with grid??

01 February 2016 2,326 7 View

How integration of PV system in a conventional distribution system is possible?

09 October 2015 2,443 5 View

How to model grid tied inverter with proper control technique in MATLAB?

How to model grid tied inverter in MATLAB_Simulink environment....... is it possible to interface three phase grid tied inverter model with single phase Buck Boost output of MPP controlled PV array?

09 October 2015 1,831 1 View

What are the current issues on connecting pv cell to electric grid???

I want to ask what are the major issues that are arising in India while connecting pv cell to grid system and how this problem can overcome??

08 September 2015 5,559 1 View

How to compare two groups with only two measurements?

Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

03 March 2021 8,796 3 View

Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence?

I am on the lookout for the Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence. Does anyone know where I can find it? Thank you in advance

03 March 2021 3,568 1 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

Do we need to write protocol for a second study of a systematic review that has been registered and published?

I have conducted and published a systematic review and meta-analysis research with the topic related to public health and health pomotion (protocol was registed in PROSPERO). Now we want to...

03 March 2021 8,920 3 View

How to increase a model accuracy ?

dear community, my model is based feature extraction from non stationary signals using discrete Wavelet Transform and then using statistical features then machine learning classifiers in order to...

03 March 2021 6,994 5 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Do I need to do linear regression before running mediation analysis using PROCESS MACRO by Hayes ?

I just wanted to check if I need to run a linear regression separately if I am using PROCESS MACRO to run mediation analysis. Thank you.

02 March 2021 4,359 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Sample dilution for quantitative analysis using ELISA?

If the detection range is in ng/ml but the reference range is in ug/ml for a molecule or protein in serum or plasma .how to dilute and what is the initial volume to be taken for quantitative analysis

02 March 2021 7,670 3 View