How to Fix my sketcher in abaqus learners?

21 February 2025 1 5K Report

The sketcher in my abaqus has different values in the x and y axes. Thus the picture given is actually a circle drawn but it's getting distorted because of the rectangular pattern of the sketcher. How can I get it to be square? FYI It has been like this ever since I freshly installed the software. Tried reinstalling it three times also. What could be causing this and what can I do to get it working properly?

Engr. Tufail

I am not sure, seeing it for the first time but the best thing you need to do is to use constraints to overcome this issue.

Badges
Science topic

Similar topics
Education
Students

More Arfanul Alam Tonoy's questions See All

I am trying to construct a 2d geometry in comsol from SEM surface image of Nanofiber mat. Do you know how to do it?

Hi, Attached is an SEM image of the nanofiber surface. I want to construct a 2d geometry (2nd image) based on solid/void binary in the comsol. I did try it by making the image binary but found...

11 February 2023 6,456 5 View

What is the problem of getting SiC fibers from polycarbosilane (PCS)?

Hello! I am following a recipe from literature to spin SiC fibers via electrospinning. I have used PCS(MW=1000-2000) and DMF & Toluene as solvents. I mixed the solution overnight with gentle...

14 October 2022 4,891 0 View

How to draw dip-slip distribution model?

I have been trying to model subsurface slip with GBIS software. However, after the geodetic inversion, i don't know how to draw the subsurface slip as shown in the screenshot. can anyone please...

23 November 2019 9,411 2 View

Why does gold nanoparticle trapping on the surface of nanofibers increase the impedance?

Hello! I am using DEP to trap gold nanoparticles on the fiber surface. I am using 15vrms and 100kHz to trap particles. After trapping gold NPs, why does the impedance increase compared to DI...

01 January 1970 1,064 3 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,831 4 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

Simulation of metal drawing by Abaqus with UMAT?

Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...

30 July 2024 7,062 1 View

Why running a restart analysis in Abaqus in Ubuntu OS gives an error as attached when running the same job in Windows doesn't give any error and runs?

I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...

29 July 2024 9,572 3 View

How Can I Apply Hashin Damage Properties to Solid Elements in Abaqus Without Using VUMAT?

Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...

28 July 2024 8,169 0 View

Abaqus cylinder buckling riks analysis?

hi, I am doing a risk analysis of a cylindrical fuselage with windows. I have applied contact interactions between the different parts, and I have applied a unit value load to a reference point,...

20 July 2024 647 2 View

Abaqus 2023 - How to know how many elements have been deleted during a simulation ?

Hi all, I am using the element deletion process based on a Tsai-Wu criterion through a UMAT with a specific State Value controlling the process (DepVar -> Variable number controlling element...

17 July 2024 1,501 1 View

How to cacualte the creep life of polycrystal with CPFEM?

I saw a paper(PHAN V-T, ZHANG X, LI Y, et al. Microscale modeling of creep deformation and rupture in Nickel-based superalloy IN 617 at high temperature [J]. Mechanics of Materials, 2017, 114:...

16 July 2024 8,436 0 View

Hello, does anyone know how I can get coordinates of two specific points on a moving body in Abaqus when applying a vdload subroutine?

Hello I am trying to simulate repulsive force of two permanent magnets in Abaqus. I have implemented Force equations into a vdload subroutine. sensitive parameters are the center to center...

15 July 2024 3,491 0 View