Am saw many journals but yet didn't find the procedure to calculate the torsional strength of the model. Please share your idea to find it.
I am working on microalgae cultivation using waste water. The initial concentration of nutrients were less but the microalgae has achieved biomass growth of 2 g/L. The final concentration of...
08 August 2024 4,812 2 View
We are doing simulations of fdsoi ncfet in synopsis tcad can someone correctly explain how to match the ferroelectric capacitance and mos capacitance
06 March 2024 7,511 0 View
I am simulating a tension test of a bimaterial specimen in ABAQUS. I would like to create different field outputs for each material, and I would like to display them in a single contour plot. For...
20 January 2024 4,613 4 View
I would like to know if it is a common reagent kit for the target amplification of both DNA and RNA, or does it show amplification only for the RNA targets. Will the presence of DNA in the sample...
18 December 2023 7,062 2 View
Currently, I am working on algae-based wastewater treatment. in order to check the effect of various parameters towards treatment efficiency, I want to vary the COD, Nitrate, Nitrite, and...
13 September 2023 3,584 3 View
How it enhance acedemic or industrial career? thanks in advance
29 August 2023 2,899 3 View
Recently I submitted the SCAPS simulated manuscript to one of the RSC journals and I have taken some of the parameters from the literature as all the SCAPS papers have done the same. can anyone...
15 August 2023 2,560 0 View
Aflatoxin concentration Zon toxin concentration Ochratoxin concentration
25 July 2023 1,636 4 View
in a typical MFC H+ ions will form in anode chamber. it is supposed to go through the membrane to the cathode. many of the research papers use CEM. how is it possible, since H+ and NH4+ are the...
14 June 2023 2,798 1 View
Currently, I am working in microbial fuel cells I want to collect secondary data and analyse it to make a predictive model. while collecting I can't find all the data in verbal form. they were in...
14 May 2023 1,000 2 View
How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...
10 August 2024 942 3 View
I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...
08 August 2024 4,831 4 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
How do you tie-break and rank these two in their strength?
03 August 2024 4,471 1 View
Machine learning (ML) has shown great potential in predicting the compressive strength of concrete, an important property for structural engineering. However, its practical application comes with...
03 August 2024 2,546 2 View
I am working on developing a MATLAB Simulink model of Wind turbine with PMSG followed by MPPT Boost converter. I have gone through so many literature and videos but I am not finding clear solution...
03 August 2024 888 1 View
Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...
30 July 2024 7,062 1 View
I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...
29 July 2024 9,572 3 View
Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...
28 July 2024 8,169 0 View