How to export/extract the L2 norm and H1 norm in Abaqus?

Vien Minh Nguyen-Thanh @Vien_Minh_Nguyen-Thanh

06 June 2019 0 8K Report

Hi everyone,

Is there any way to export the L2 norm and H1 norm (not the error norms) of the calculated solutions in Abaqus?

Thanks, Minh

Badges
Science topic

Similar topics
Phytochemistry
Extracts

More Vien Minh Nguyen-Thanh's questions See All

Is anyone who knows how to buy AMOS sofware?

I have been working in Hanoi University of Public Health. I would like to know where and how I can buy AMOS software?

28 June 2024 6,593 1 View

Can I use "Confidence intervals bias-corrected" instead of "p-value" for the result of "specific indirect effect" in SmartPLS 4?

In my testing of statistical significance by bootstrapping, p_value shows that there are no specific indirect effects, but confidence intervals bias corrected 2.5% - 97.5% does not contain the...

18 April 2024 7,913 7 View

Why benzaldehyde ortho hydrogen is more deshielded than para hydrogen?

I am doing NMR practice, and the task is to assign the 1H NMR to the correct proton on benzaldehyde, while I think that the conjugation effect contribute mostly to the solution but the ortho...

24 March 2024 4,801 0 View

Coliform, Fecal Coliform, E.coli – SMEWW 9221: Multiple-tube fermentation technique 3 or 5 sample-portions? How to combine E.coli results?

1.1. 3 or 5 serial sample-portion (dilutions) SMEWW 9221C indicates the use of 3 and 5 sample sample-portion (10, 1, 0.1 ml). As I understand, both are fine. If using 3, you can dilute the sample...

21 December 2023 7,151 0 View

PLS toolbox in R?

Hello everyone. I am currently utilizing the R platform for my work. Leveraging free packages in R significantly aids in the successful completion of my tasks. I faced challenges while conducting...

30 September 2023 4,417 3 View

What is the "Error: floating point exception | Error Object: #f" in fluent (Ansys)?

Hello everyone! I'm doing CFD propeller marine. But I am errored. Can you help me? Error at Node 0: floating point exception Error at Node 1: floating point exception Error at Node 2: floating...

31 March 2023 7,322 2 View

Why the baseline increases while using water with HPLC-ELSD?

I am using Agilent Infinity II ELSD (G4260B) to develop a new analysis method and facing these problems. 1. Large baseline offset: When turning on the system (parameters as below), the signal was...

15 March 2023 4,767 2 View

How to avoid RBC contamination during PBMC isolation?

1. After using a Ficoll gradient to isolate PBMCs, once in a while I notice a red blood cell contamination of my PBMC interphase after centrifuging (Files attached). Therefore I wonder what I’ve...

30 November 2022 7,134 4 View

Why performing a shotgun proteomics analysis is an important initial step before a SWATH experiment?

Explain why performing a shotgun proteomics analysis is an important initial step before a SWATH experiment.

16 November 2022 7,499 0 View

Is the Lyovapor L-300 system really effective?

Hi all colleagues, I currently own a Lyovapor L-30 system provided by Buchi. I own this system from 2020 until now still can't use this system effectively. Even though the sample was frozen, the...

05 September 2022 7,300 0 View

Strugglling with m6A dot blot any suugesstion ?

I have been doing the m6A dot blot for a while with no improvement, I am extracting the RNA, and I can see the dots although the three biological replicas give a different reading on the memberan...

10 August 2024 8,539 5 View

How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?

09 August 2024 7,718 0 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,831 4 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

The aqueous fraction of the hydroethanolic extract is showing the presence of palmitic acid. What is the mechanism responsible ?

Palmitic acid presence in aqueous fraction

05 August 2024 8,624 4 View

How to set the environment variable for incorporating the GD3 dispersion in G16 for performing calculations using the OPBE functional?

I have incorporated the dispersion effect for the OPBE functional by specifying the S6, SR6 and S8 parameters for GD3 in Gaussian G09 package. For this purpose, I have defined the environment...

05 August 2024 1,494 2 View

Which solvent is better to dissolve with secondary metabolites extracted from fungi?

I work on MCF7 cell cell for anticaner purpose and I wa to do drug preperation the drug ( secondary metabolites extracted from Aspergillus) My question which solvent is better with these secodary...

03 August 2024 4,725 2 View

For systematic review data extraction, should I use ITT or PP analysis, and count all randomized participants or only those who completed the study?

I am conducting a systematic review and meta analysis; as I am extracting data I realized there is a consort diagram that shows the number of patients from randomization till end of the study. So...

01 August 2024 9,993 3 View

For the moringa oleifera extract using ethanol as the solvent,what is the alternative method to concentrate the extract other than rotary evaporation?

99% pure ethanol was used for maceration also alternate methods along with the temperature and time to concentrate the extract can be specified

31 July 2024 5,113 4 View