How to execute bash script in cgywin?

More S. Xavier's questions See All

Sample dilution for quantitative analysis using ELISA?

If the detection range is in ng/ml but the reference range is in ug/ml for a molecule or protein in serum or plasma .how to dilute and what is the initial volume to be taken for quantitative analysis

02 March 2021 7,670 3 View

What are the new 2D nanomaterials were used for Silver nanoparticles stabilization?

In the stabilization of AgNPs are vital in current research interest. However, some of the 2D nano-materials like graphene oxide, MoS2, etc... previously used to stabilize it. But still they shown...

01 March 2021 2,207 3 View

What information can be had from raman at higher wavenumber?

i have recorded raman spectra of strontium oxide thin film. the spectra were recorded in the range 400 to 4000 cm-1. i have reference to peaks upto 1000cm-1. but i couldn't find literature for...

26 February 2021 2,499 1 View

What are the methods used for CNT..?

Respected Professor's i hope you are doing well and happy. i need some information about carbon Nanotubes. before blending the CNT with the matrix the CNT has been introducing in some treatments....

24 February 2021 5,383 5 View

Langevin Dynamics in shear flow?

Hi, We are trying to simulate particles with Langevin dynamics in a shear flow by Lees-Edwards boundary conditions in MD simulations. It seems thermal forces and shear flow do not go hand in...

23 February 2021 1,761 1 View

How we can measure Kemp % in wool without using of benzene?

Would you please let me to know about the methods for measurement of medullation and Kemp % on animal? My problem is that the wool sampling and sending to laboratory is not possible. So I would...

21 February 2021 7,260 4 View

Which is the best software or programming language (user friendly) for analysing data?

I have a basic knowledge on Python, R and MATLAB in analysing data. Among those, which is the best and user friendly? Which one should I learn deeply to analyse data?N:B: I want to learn data...

20 February 2021 3,950 15 View

Hi..how to isolate crude HDL (all subfractions) from human serum by size exclusion chromatography?

I would like to know about isolation of crude HDL from serum by SEC. Is it possible to perform with a serum sample volume of

19 February 2021 5,576 2 View

What is the reason film thickness increased?

what is the reason film thickness increased when increased doping concentrations give some reasons The measured film thickness is 156, 282, 394, 548 and 681 nm for 0, 1.5, 2.5, 3.5, and 4.5 wt....

17 February 2021 8,987 5 View

Do you have any experience with transfection of EBV immortalized B cells with Lipofectamine?

I know that efficiency of transfection for primary B cells is very low with Lipofectamine. But I did not try that for EBV immortalized B cells. Do you have any experience with transfection of EBV...

05 February 2021 4,159 1 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

How to modify Johnson cook equation in ABAQUS?

I wanted to add an extra parameter to the existing Johnson cook equation in the ABAQUS simulation. How to add those extra parameters. Ref: A modified Johnson-Cook material model with strain...

28 February 2021 4,841 3 View

Bayesian decision trees and bayesian regression trees in Python and/or R?

I am looking for implementation of bayesian decision trees and bayesian regression trees in Python and/or R.. Do you know if the existing libraries support this

23 February 2021 6,689 3 View

How can we estimate sample size for a moderated mediation analysis with more than two mediators?

How can we estimate sample size for a moderated mediation analysis with more than two mediators? I am looking for scripts, macros, syntaxes, that allow us to estimate sample sizes for research...

15 February 2021 6,813 3 View

In Abaqus, is it possible to remove elements which are too complex for meshing from a sequence obtained by getByBoundingBox() ?

Hello everyone, I'm trying to mesh a structure with complex partitions using mesh controls. When doing it on the user interface I'm first selecting all cells. In the following, I have to accept...

03 February 2021 8,198 1 View

How to annotate list of gene names using Bash/R?

I have a list of gene names from deep sequencing from a constructed CRISPR knockout library. I was hoping to write a script to annotate all the gene names with a quick description of product...

27 January 2021 8,035 1 View

How to calculate j-integral for 5 contours by abaqus script and retrieve the values ?

I mean I am looking for a code to retrieve the values of each contours and I have written the code below but It doesn't work... Jint= odb.steps['Step-1'].historyRegions['Assembly...

21 January 2021 277 3 View

How to add a single parameter in Ansys Additive Manufacturing Workbench parameter setting dialogue box?

Ansys 19.2 R2 and 2020 R1 versions of Additive Manufacturing Workbench is convenient for powder-based Additive Manufacturing processing. However, in this workbench, there is a machine parameter...

19 January 2021 3,017 2 View

How to script VMD tcl within bash script?

Greetings, I want to run a vmd script within my bash script. I am using the text only version of VMD for linux for my windows terminal ubuntu subsystem and I would like to generate code within my...

16 January 2021 192 5 View

Can anyone helps me with Autodock 4.2 scripts error ?

After opening the file, I operate command "Script" --> "Ligand Interactions" --> "Show Ligand Binding Site Atoms" and the warning appears as "This script displays ligands and surrounding...

15 January 2021 5,360 1 View

Martin Klvana

1. Install Cygwin package including Bash (bin/bash.exe).

2. Create ".bashrc" file in the user home directory; customize Bash behavior.

3. Point to the ".bashrc" file from ".bash_profile" file, located in the user home directory and containing the following text: source .bashrc

---

4. Make the Bash script executable: chmod +x script.sh

5. Execute the script: ./script.sh

Cygwin terminal emulator: Mintty

https://mintty.github.io/

S. Xavier

Thank you for the reply...