I want to estimate the mass (does not have to be accurate) of a centrifugal compressor knowing the required mass flow rate and pressure ratio.
Thanks in advance!
The weight of the compressor is usually given by the manufacturer. Consult their catalogue
Salam everyone, So I am trying to extract DNA from isolates of clinical samples of staphylococcus aureus, I am using a QIAamp UCP kit. I followed the same manufacturer protocol and used Qubit to...
03 July 2024 3,892 1 View
I use MATLAB to define SAP Model using API function but when trying to define time history direct integration case, the non-linear parameters change from the default which affect the results and...
04 June 2024 2,369 1 View
I need it uopn a reviewer's request to make a 500ns MD
07 February 2024 7,667 3 View
Graduation projects animal biotechnology plant biotechnology microbial biotechnology bioinformatics
04 December 2023 3,530 9 View
I am performing qRT-PCR for zebrafish different organs and tissues using sybergreen and elongation factor 1-alpha elfa as a reference control. However, there is variation in the expression levels...
29 November 2023 9,309 2 View
or even the Effect of Planning on Tax Evasion. Thanks in advance,,
10 September 2023 2,941 3 View
I did CHIP qPCR for transcription factors on a promoter, I got fold enrichments (compared to control IgG) as 2.54, 2.75, 3.45 and 21 for diffferent transciption factors in different sites. Can...
28 August 2023 4,797 0 View
hello, Currently, I have MRI data results for Wistar rats, examined to confirm the induction of multiple sclerosis. However, i don't know how to interpret these images! I would very much...
29 June 2023 9,285 4 View
I use a HMC5883L-type electronic compass connected to Arduino and I got the code programming that gives me the angle of regression but the problem is that when I tested it I found that it showed...
23 June 2023 5,088 0 View
Free Valproic acid
05 June 2023 3,378 0 View
Can anyone explain this method? Especially the last statement where it says only at 1.5 to 2.5mins was the MS/MS connected to the UPLC. How is that possible, is it a feature in this specific...
11 August 2024 8,141 3 View
Hello experts, Does anyone know any free software about retention index prediction ?
08 August 2024 7,403 2 View
I'm currently working on calculating the collision cross section (CCS) for various ions, and I'm facing challenges when dealing with sodiated and multiply charged ions. Most of the resources I’ve...
08 August 2024 8,329 0 View
I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.
07 August 2024 4,526 4 View
Hello, I suspect that a molecule I am using is causing bacteria to experience osmotic shock. What chemical properties should I look for to compare this capability with those of other substances?...
06 August 2024 977 1 View
To compare positive and negative cell populations in flow cytometry, should I compare unstained cells with antibody stained cells? Or with the isotype control? Most papers show comparison with...
06 August 2024 6,728 6 View
Women, on the other hand, can become physically aroused (increased blood flow in the reproductive organs) without becoming psychologically aroused even in the slightest. (Robert Weiss)
05 August 2024 9,537 2 View
We have a lateral flow test on Sartorius 140 NC. The conjugate is gold-monoclonal antibody. Using different control lines (GAM, protein A, protein G) we get a very strong leading edge with reduced...
31 July 2024 4,510 3 View
I want to perform a CRISPRa/i library screening for candidate regulatory factors that affect pathogenic Th17 differentiation in PBMC. But I am wondering how to define the size of gene library, so...
31 July 2024 2,150 0 View
EDX analisys
31 July 2024 5,947 2 View