Protocol for doing SARS-CoV-2. sequencing ?

Hey every one I am wondering if you have the protocol or the methodology for doing NGS for the SARS-CoV-2 virus gene?

16 June 2020 7,555 7 View

How to compare the computational efforts when the computations to be compared are being run on different computers with different CPU and RAM?

Consider you have two computational methods to solve a specific problem (also the corresponding software) and want to see which method is more efficient for the specific problem. Is it possible to...

31 May 2020 7,512 6 View

Is it possible to see the redox peak in CV while did not observe plateaus in the charge-discharge curves?

Dear researchers I see clear redox peaks in CV, but i did not plateau in the charge-discharge curves. Does anyone know the reason?

04 February 2020 707 9 View

What is the nonparametric equivalent to standardized response mean?

My supervisor has suggested I do the standardized response mean to measure longitudinal change of different parameters in motor neuron disease patients. Some of the data are non-normally...

01 July 2019 10,015 2 View

Killer cells were stimulated with anti CD3, CD28 to produce cytokines, brefeldin A was added but no expression of cytokines. any suggestion?

CD8+ T cells, NK, NKT cells were stimulated by anti CD3, CD28 for 1 hour, 4 hours, 24 hours to produce cytokines. Then, brefeldin A was added after stimulation times to keep cytokines inside...

01 October 2017 7,474 3 View

Contact between a hyperelastic membrane tube and an elastic membrane plate in abaqus explicit?

Hi, I am trying to solve overclosure contact problem between a hyperelastic membrane tube and an elastic membrane plate during pressurizing uniformly the tube in abaqus explicit. Using suface to...

30 September 2017 1,149 4 View

Hi, for some reasons my brefeldin A is not stopping cytokines secretion, any body got any suggestions?

05 September 2017 5,131 3 View

How can I measure the residual of the trait values?

I want to compare evolution rate between two set of data (morphological and reproductive traits) because the values of the reproductive traits is very small in compare with morphological traits...

17 May 2017 6,374 2 View

What are the most valid ranking measures (websites) for impact factor?

I am looking for the most valid measures (websites) that calculate the impact factor! This because the fact that there are several websites, and one site may show a different ranking of impact...

27 February 2017 7,119 8 View

When should funnel plot figures be used?

Is there any minimum number for studies that should be included to create funnel plot figure? Any recommended sources or guidelines to follow would be appreciated!

17 February 2017 5,439 2 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

How climate change will influences human and animal behavioral change?

The role of climate change influencing the human behavior as well as economics interest

01 June 2021 0 0 View