How to determine the composition of a compound from the atom% data from EDX of SEM/FESEM?

09 September 2018 0 10K Report

SEM/FESEM

Badges
Science method

More Tuhin Subhra Dash's questions See All

Why a material (such as iron) is ferromagnetic? What are the factors a material considers before choosing ferromagnetic/antiferromagnetic ordering?

1) Any Thermodynamic factor(Energy, Entropy) Gain or Loss? 2) Any Quantum Mechanical phenomenon involved? 3) I want to know Why? not How?

05 June 2017 6,321 3 View

What are the factors for successful doping of a chemical element in a solid state synthesis method?

Size? Charge? Anything else? In details please?

05 June 2017 715 3 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

1. If I can quantize the atom using this hyperbolic spiral and classical physics, could nature do the same?

If we map as a continuous motion an ionising electron (beginning its journey at n=1) in an H atom, a specific hyperbolic spiral appears (see animation). When we solve this spiral formula, we find...

07 August 2024 5,343 2 View

Gromacs first step of minimization ?

I have face this problem anyone help me how to solve this issue ?which is below Fatal error: There are inconsistent shifts over periodic boundaries in a molecule type consisting of 78 atoms. The...

07 August 2024 2,598 1 View

Should I include H atom into C3N5 when i am doing DFT modelling?

Hi all, my experimental XPS results shown that my C3N5 sample consists of N-H bond, hence in this case I should incorporate the N-H bond into my DFT modelling. However, I do notice several papers...

07 August 2024 8,414 2 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

How does grain and grain boundary affect the ceramic when studying its dielectric properties?

I am not able to get good literature and the physics behind how first these grains and grain boundaries arises out of no where when we make a pellet to study its dielectric properties and then how...

07 August 2024 5,177 3 View