How to determine p,r and d in a river discharge modelling by SETAR (model)?

Nasrin Fathollahzadeh Attar @Nasrin-Fathollahzadeh-Attar

05 March 2019 0 4K Report

I want to model river flow by self threshold autoregressive model, but I don't know how should I consider these three (p,r,d)?

please help me.

Thanks,

Nasrin

Badges
Science topic

Similar topics
Engineering
Modeling

More Nasrin Fathollahzadeh Attar's questions See All

If the emission of all greenhouse gases is stopped now, will the temperature of the earth continue to rise?

Here's a serious question: If we were to stop emitting all greenhouse gases right now, would the Earth's temperature start to cool down, or would the existing greenhouse gases continue to warm the...

30 July 2024 5,123 4 View

What is the good dilution factor for mouse serum in ELISA?

I am doing IL6 ELISA to measure mouse serum IL6, but my ODs are so low even for mouse on two weeks high fat diet. My standard curve is good enough as a positive control.

28 April 2024 8,922 2 View

Agglomerated Green synthesized CeO2?

Dear colleagues i have synthesized CeO2 using green method and now the Np are not soluble in water how can I make it soluble in water? Best Regards

18 March 2024 4,496 2 View

Biocompatible stabilizers soluble in pbs?

Dear colleagues what are the biocompatible stabilizers that are soluble in PBS and can be used in anti cancer treatments?

15 March 2024 8,003 1 View

Can you help me by answering the following questionnaire?

Hello dear teachers, I am currently conducting a research study for my master's degree, and I need your valuable contributions during this process. My survey is designed to explore factors that...

19 February 2024 1,138 0 View

Zero point charge?

How to determine the zero point charge for a schottky barrier or a composite consisting of more than one oxide for photocatalytic degradation ? Thanks

16 December 2023 478 6 View

Which type of glue can be used for peeling test?

I want to do peeling test on commercial cathode and anode electrode. Is there special glue tape for testing?

28 November 2023 8,548 2 View

How to best analyse a sensory evaluation records?

Hello all, Hope this message finds you in good health. I am trying to analyze sensory data "9-hedonic scale" using RStudio, What is the best analysis to use, and is there a script I can...

18 November 2023 3,002 3 View

Does anyone have experience using Forced Intercalation-Peptide Nucleic Acid Probes (PNA-FIT) labeled with thiazole orange dye for qPCR?

The first question is, should they take out of the lyophilized state with a special solution such as formamide? Based on the experience that we used to remove the TaqMan probes from the...

05 October 2023 6,532 0 View

How to prevent the aggregation of positively charged nanoparticles in the aqueous environment?

I have made positively charged nanoparticles with Lecithin, Squalene, Tween 80, Span 85 and Dotap. But after using ultrasonic, the particles are aggregated and their size increases. How can...

10 September 2023 3,280 3 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

What are the key methods and indicators used in assessing the biodiversity of river ecosystems, and how do these methods account for variations ?

Biodiversity assessment of river ecosystems is crucial for understanding the health and stability of these environments. This question aims to explore the various techniques employed to evaluate...

07 August 2024 4,290 3 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Is there an alternative to a multinomial regression which allows the DV to be non mutually exclusive?

I am trying to analyse data from a survey examining what variables affect teachers perceived barriers to incorporating technology into their classroom. I have 5 predictor variables however my DV...

06 August 2024 1,752 3 View

In order to run Multinomial Logistic Regression, is it required that the data be in the long format?

I am using unit level data (IHDS round 2) & Stata 17

06 August 2024 5,725 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View