How to determine encapsulation efficiency based on FT-IR absorbance?

More Hossein Azarian's questions See All

How many percent cell viability is necessary (minimum) for a material to consider as bio-compatible or non-toxic for wound dressing application?

To protect the wound from infection and keep the skin cells functioning, at least how many percent of cell viability is required?

09 October 2017 8,148 0 View

I'm looking for a good reference or handbook of X-ray photoelectron spectroscopy (XPS) of polymer composite thin films. Anyone can help?

I want to analyze the higher resolution XPS spectra in the C1s region.

09 October 2014 7,122 2 View

What are the effects of the surface roughness on Thin film properties?

I prepared thin films of Pani-DBSA/Natural rubber and characterized their surface morphology by Atomic Force Microscopy. The average roughness is around 60 nm

04 May 2013 7,453 17 View

Is it possible to cast the thin film on the wafer silicon or any other substrate and measure it's conductivity by four probe conductivity meter?

Actually I work on polymer blending, I mix polyaniline/DBSA and natural rubber and produce the thin films from them by the solution casting but the problem is that films are very sticky and can...

03 April 2013 4,182 9 View

How to learn more about SPSS and its Application?

I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.

11 August 2024 9,101 4 View

Can I base on reverse DNA sequences to perform alignment, convert to amino acids and GenBank submission?

I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?

11 August 2024 5,138 1 View

Baseline drift in HPLC? What causes this?

Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!

11 August 2024 3,770 4 View

Text-Communication from the M1 Hand Area using BCI—and then there is Elon Musk?

Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...

10 August 2024 7,180 0 View

Has anyone applied Python in the field of textile engineering for data analysis, automation, or smart textiles?

I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...

10 August 2024 7,429 2 View

Strugglling with m6A dot blot any suugesstion ?

I have been doing the m6A dot blot for a while with no improvement, I am extracting the RNA, and I can see the dots although the three biological replicas give a different reading on the memberan...

10 August 2024 8,539 5 View

How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?

09 August 2024 7,718 0 View

How are iso-frequency contours plotted?

Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...

07 August 2024 1,937 1 View

How to prepare the nanoparticle treated fungal sample for Environmental SEM analysis?

A fungal strain was treated with nanoparticles. We want to do an environmental SEM analysis. So could anyone share your views on preparing the sample? Thank you.

07 August 2024 5,307 1 View

How to normalize and take the significance of the MTT OD values with 3 replicates for the same cell-line?

Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...

07 August 2024 8,106 4 View

Robert Kiss

You should contact Prof. Erik Goormaghtigh ([email protected]) who is an actual specialist in FTIR spectroscopy.

Best regards

Robert

Leonid V Vladimirov

If by the "encapsulation efficiency" you mean the rate of release of plant extract from

gelatin capsule - there is NO WAY by using FTIR - to achieve this goal.

Why don't you use just the weight loss of the entire capsule ?

Leonid

Elham Tavassoli

This article might help you

Electrosprayed gelatin submicroparticles as edible carriers for the

encapsulation of polyphenols of interest in functional foods.

Food Hydrocolloids 49 (2015) 42e52