How to design a Quadrotor so as it can fly in varied trajectory?

11 November 2014 0 8K Report

Design requirements that are generally required to develop a quadrotor to fly in trajectory such as circular and square without motion capture camera.Suggest few tips to model a simulation/Algorithm for quadrotor model.

Badges
Science topic

Similar topics
Philosophy Of Science
Models

More Julin J B's questions See All

What is the difference implicit guidance and explicit guidance?

I need a clear definition on implicit and explicit guidance scheme used in missile and launch vehicle.Recommend some text book if possible

04 May 2015 8,961 0 View

What do poles zeros in a transfer function mean?

I need a simple definition of pole and zero over a transfer function , I expect a non mathematical explanation.

31 December 2014 227 2 View

Can a quadrotor perform an aggressive manoeuvre without a motion sensing camera?

Aggressive manoeuvres performed by quadrotor in the lab are generally done by motion capture camera. Can these manoeuvres be done without a motion camera under open atmosphere?

10 November 2014 1,624 5 View

Can comsol multiphysics be used for pulsed plasma thruster simulation?

By combining both ac/dc module and plasma module to simulate it?

03 April 2014 5,661 2 View

How can a spark plug can initiate a spark/plasma/electric arc in vacuum?

Much thanks.

01 February 2014 3,634 1 View

Is it possible to design an ignition circuit and simulate in simulink?

Seeking tips for designing a ignition circuit in simulink with spark plug.

31 December 2013 8,901 1 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

What analysis to choose with a large neste dataset and clearly skewed or kurtotic distributions?

Hello! I have a dataset of n=3000 nested within 8 countries with approximately 200 or 400 responses in each country. I originally planned to perform multilevel modelling with 4 dependent variables...

02 March 2021 6,865 1 View

Is there a deep reason for using the squared modulus of the wave function as the probability density of the existence of the particle?

I think we were all surprised at the first time we got to know quantum mechanics that the squared modulus of the wave function is the probability density of the existence of the particle? The role...

28 February 2021 6,282 9 View

What could be reason for getting such type of graph for complex impedance in case of polymer blend films?

Its effect appears in real part of ac conductivity also. Can anyone suggest any reason behind it?

26 February 2021 3,487 3 View

How to plot the probability paper of Gumbel distribution using R programing?

In R-studio, there are many commands of Gumbel package. Arguments are also different. I`m asking about the alpha parameter of the Copula which must be greater than 1. If this is the one used to...

25 February 2021 5,229 3 View

Why do the air flow results vary totally when adding scalar in CFD ?

Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...

25 February 2021 9,602 4 View

Are there methods for automatically mapping floodplains, fans and terraces?

I want to map these river geoforms with as little subjectivity as possible. I have a high resolution DEM generated by drone data.

22 February 2021 7,800 3 View

Resistivity of PVD TiNx thin films vs. N2 flow?

In the PVD of TiN thin films (~100A), I've found the resistivity of the TiN films dropped from ~100 to 60um*cm with N2 flow increasing up to the metallic mode ending point; then the resistivity...

21 February 2021 1,864 2 View

How do I add a udf to Ansys fluent and does it need to be compiled before hand ?

I have a Define_CG_Motion udf written in c where do I add it to my Ansys fluent project and does it need to be compiled before that?

21 February 2021 9,347 3 View

How to implement boundary conditions in Abaqus contact problems?

Hello I am trying to simulate crawling motion of a bilayer beam using Abaqus. Kind of similar to this: https://youtu.be/os-Z3ucoFpA I am using multiphysics enabled (diffusion, deformation,...

20 February 2021 2,916 1 View