How to describe the inclusion size and distribution in plate steels apart from inclusion chart.

01 January 2014 0 2K Report

The thin -heavy inclusion rating method suffers as sulphides are no longer elongated in case of pipeline grades, and hence control on their size may be required for standardization rather then the aspect ratio.

Badges
Science topic

More Rajinikanth V's questions See All

What is the suitable macroetchant to revel the large clean grains of CRGO steel?

High silicon content leads to severe pitting problem when conventional etchants are used.

09 October 2017 6,025 2 View

What grade of photographic paper is good for sulphur printing ?

anyone with experience of sulphur printing on rails. kindly reply.

05 June 2015 297 0 View

What are the suitable etchants to determine prior austenite grain size in hot rolled steel sample?

Especially for microalloyed steels

31 December 2013 4,717 9 View

If I increase the voltage in Electron backscattered diffraction ( EBSD), what will happen to the spacing of bands in the kikuchi pattern?

What is the relation between actual d-spacing of crystal to the spacing observed between the excess and deficient lines of a kikuchi band? I thought it was just 1/d but actually it is not true. Why?

05 June 2013 5,441 2 View

What should be limiting carbon content of steel one should consider while indexing martensite phase as ferrite /martensite by EBSD?

The reason i ask this, my steel has 0.15%C, and contains both retained austenite and martensite , the retained ausenite fraction varies depending on whether i choose ferrite or martensite for...

01 January 1970 7,539 3 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

I have get this error when i calculated the geometrical optimization for prco3, it takes 12 hours until gives this message in the outputfile?

Fatal error in MPI_Allreduce: Other MPI error, error stack: MPI_Allreduce(1628)......: MPI_Allreduce(sbuf=000002459254A180, rbuf=000002459F86A140, count=4851, MPI_DOUBLE_COMPLEX, MPI_SUM,...

09 August 2024 7,615 1 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Why does my protein refolded to beta sheet during thermal denaturation analysis?

Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...

06 August 2024 1,989 3 View

What is the prepared reference material that can be used in inductively coupled plasma optical emission spectrometry (ICP-OES) to measure REE and U ?

What is the prepared reference material that can be used in the ICPE-9820 Shimadzu Japan instrument, which employs inductively coupled plasma optical emission spectrometry (ICP-OES) to measure...

06 August 2024 1,896 1 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

How effective is the Citi Bloc standard basket in enhancing the accuracy and comparability of international construction cost assessments?

Citi BLOC Standard Basket Definitions: A standardized unit representing a fixed basket of construction materials, labor, and equipment costs priced in various cities. Purpose: To create a common...

04 August 2024 8,997 1 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View