Hi, I am trying to set circular polarization propagation from a point source towards a glass substrate in 3D simulations. what should be its electric field components to vary its incidence in both polar and azimuthal directions in 3D?
Thanks
Hi, Sriram, What you mean by control here? Can you elaborate? which software or calculation method you are using?
Is the electropolymerisation of polyaniline coating over stainless steel (SS) via Cyclic voltammetry technique is really adherant? Else how to improve the adhesion of the coating, whether any...
01 March 2021 8,220 2 View
I have come through a few literature,were the presence of particular clay mineral has been validated through the Si:Al ratio obtained from EDAX analysis. But, I would like to understand the basic...
08 January 2021 5,982 6 View
What are the application of graph theory to fluid mechanics? Kind help if any papers kind help Any relation to 1) distance in graphs 2) graph coloring 3) graph Decomposition Or any other fields...
08 November 2020 9,974 3 View
18 April 2020 7,990 3 View
In LES non-premixed combustion of propane-air in Ansys fluent, there is no signs of combustion. The temp. is 300K everywhere. How to overcome it?
05 April 2019 9,809 12 View
Upon stability, the assay reduces to 91 to 92% but the remaining 8 to 9% is not being compensated by impurities. Assay and RS, both methods have been developed using HPLC. To identify...
21 January 2019 2,576 4 View
The picture attached herewith is giemsa stain of mouse liver - i wish to know if these nuclei that are seen are that of macrophage or myelocyte -myeloblast or basophil or mast cell ?
11 December 2018 1,141 1 View
I want to know which inforcement in the metal matrix composites increases the electrical conductivity of it. Also, state the reinforcement to reduce the thermal expansion. Kindly mention some...
31 August 2018 9,557 3 View
I want do some research in 3D printing in the field of metallurgy
29 June 2018 9,771 2 View
03 August 2017 1,188 3 View
When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.
16 June 2021 0 0 View
I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...
03 March 2021 4,116 4 View
Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...
02 March 2021 2,431 3 View
Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...
02 March 2021 4,910 3 View
Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...
01 March 2021 9,537 2 View
I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...
01 March 2021 6,661 3 View
Hi In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein? I got this error in the add-ion stage: Fatal error "./ amber99sb-ildn-HHH.ff / force...
01 March 2021 8,747 4 View