On what conditions dopants replace the host elements?

I doped Sn-Sb alloy with Ti,Cu and Ce elements individually (@ 25 wt % as replacement to Sn). From EDX calculation, the elemental compositions are Sn1.38Sb3.60, Sn0.85Ti0.37Sb3.86,...

31 December 2017 7,556 2 View

Why do sometimes Nyquist plots show different z' and z"values?

In Nyquist plots, x axis holds resistance part and y axis holds reactance of this resistance on current-voltage characteristics (pls correct me if I'm wrong). But sometimes we do not observe equal...

08 September 2017 8,395 0 View

How does type of crystal system affect the electrical conductivity of a material?

What is the influence of type crystal system and crystallographic orientation on the electrical properties of a material?

01 February 2017 7,412 0 View

What is the reason for new peak of LLTO in Raman spectra?

07 August 2016 834 3 View

How to find the elemental composition of a material without EDX& ICP?

.

06 July 2016 1,358 2 View

Sutter electrode holder leaking after applying positive pressure. How to fix?

I am using a Sutter electrode holder for my patch clamp experiments, but I'm having trouble keeping positive pressure inside my electrode due to a leak out of the back of the holder. I have added...

02 March 2021 5,829 1 View

What thickness need for ITO to use as conductive layer?

I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...

01 March 2021 395 3 View

Adherance of Polyaniline coating over stainless steel?

Is the electropolymerisation of polyaniline coating over stainless steel (SS) via Cyclic voltammetry technique is really adherant? Else how to improve the adhesion of the coating, whether any...

01 March 2021 8,220 2 View

What is the indication of the absence of peaks in Methanol electrooxidation CV curves ?

I have several question regarding the MOR; hope anyone help me better understand. 1- in CV using (KOH+MEOH) what is the indication of absence of the redox peaks? shouldn't they exist as a sign...

28 February 2021 4,851 8 View

Why is my platinum counter electrode getting dirty during electrodeposition?

I am conducting anodic electrodeposition of MnO2 onto a stainless steel substrate, using a platinum strip as a counter electrode. This is done galvanostatically, with the current held between 5...

27 February 2021 1,829 3 View

How does charge on working electrode changes with rising potential?

During performing CV of a GCE or modified GCE, we rise the potential in the first half of the cycle and reduce it in reverse half. During the first half, what is the nature of charge on GCE or...

25 February 2021 7,994 3 View

How to troubleshoot Electrochromic Films and Electrochromic Devices?

I am trying to characterize an electrochromic system. The system uses ITO electrodes on glass, WO3 as the electrochromic film, and NiO as the ion storage layer. When I deposit NiO and WO3 and...

23 February 2021 9,592 2 View

How does elongation affect the resistance of an electrode?

What are the testing rate for electrodes recommended by ASTM for cochlear implants. I am currently doing the 15mm/min elongatio testing.

22 February 2021 1,515 1 View

Is that possible to do an impedance measurement without FRA module?

One of my colleagues said, "the impedance you can measure with the three electrodes and with the specific sequence varying the frequency" Is it possible to configure the potenciostat without the...

21 February 2021 418 2 View

Do you know this error? The experiment was stopped by a potential overload on Vs (auxiliary electrode)?

Hello everyone Do you have any information about this error 'The experiment was stopped by a potential overload on Vs (auxiliary electrode)' in Origamaster software? I tried everything possible,...

19 February 2021 3,152 7 View