How to compare or correlate estuarine primary production, secondary production, tertiary production with benthic production?

More P. R. Jayachandran's questions See All

How to heat polymer for about 130° without oil bath ?

is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it

06 August 2024 947 1 View

Ti6Al4V - Phase differentiation between alpha and alpha prime martensite?

Dear Researchers, Is it feasible to distinguish between alpha and alpha prime martensite in the Ti6Al4V alloy under rapid solidification in the as-cast state using XRD, in addition to...

30 July 2024 3,849 0 View

Is coulombic efficiency (CE) same as electron distribution % of current as mg of chemical oxygen demand (COD)?

To determine the % of different electron sinks in MFCs, electron distribution (%) is represented as mg COD (eg: initial sCOD = 100%, current = 34%). Is this value of electron distribution same as...

30 July 2024 5,221 0 View

How to interpret results of AST for Pseudomonas aeruginosa?

While doing AST for Pseudomonas aeruginosa, after incubation, no zone of inhibition observed in the plate near the well. wells surrounded by bacterial growth, when the same plate observed under UV...

25 July 2024 9,229 1 View

Flow through curved domains?

Hi everyone, I am working on a curved domain in which a ship is situated in the middle (geometry is given below). In my understanding the general fluid flow is parallel to the x axis from inlet to...

25 July 2024 9,058 4 View

What is the Principle of Cysteine-carbazole-sulfuric acid reaction with glucose?

I have been looking for the principle of Cysteine-carbazole-sulfuric acid reaction in research papers and books, but couldn't find it. This reaction is mainly used for the quantification of...

23 July 2024 3,891 0 View

How can AI technology to enhance the agricultural productivity?

Farmers no longer have to apply water, fertilizers, and pesticides uniformly across entire fields. Instead, they can use the minimum quantities required and target very specific areas, or even...

22 July 2024 8,296 3 View

Reversed flow at outlet due to the release of DFBI?

Hi everyone, I am working on a simulation involving restricted canal with ship using DFBI. I am facing reversed flow in my outlet boundaries as the DFBI is released (In 1.25s). Is there any...

17 July 2024 7,032 1 View

Can a paper that is posted as a preprint in a database with DOI, can be reviewed in another journal and accepted for publication??

It happened that I am asked to review a paper for a journal. Incidentally, the paper is posted as a preprint in another database as open access with DOI. It is completely citable. Now, should I...

17 July 2024 1,831 4 View

Do software tools exist to assess the economic and technical practicality of introducing new food products, such as yogurt with modified starch?

This question explores the world of food innovation and asks if there are computer programs that can analyze the financial and technical feasibility of introducing new food products. For instance,...

13 July 2024 7,446 0 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Do I need specific antibodies to stain for a fusion protein?

I am staining some brain sections stored in cryoprotectant that express a Histone H2B- GFP fusion protein that were generated ~10 years ago. I know I need to enhance signal with an anti-GFP...

07 August 2024 5,338 2 View

Hello Everyone ! I'm looking for a good journal to publish my manuscript with low publication cost?

I am Looking for a Science Journal with good impact factor and low publication cost to publish a review paper. Your suggestions would be appreciated.

06 August 2024 6,796 3 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

How can I improve the quality of lamb milk replacer for machine feeding?

Hello everyone, I am researching ways to enhance the quality of lamb milk replacer for machine feeding. I would appreciate any insights or recommendations on the following: Manual vs. Machine...

06 August 2024 6,227 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View